Additional Resources: Product Page 3D Model date 12/21/2015 page 1 of 32 SERIES: NDM2Z-25 DESCRIPTION: AUTO COMPENSATED, DIGITAL DC-DC POL CONVERTER GENERAL CHARACTERISTICS FEATURES 4.5~14 V input range pin and function compatible with 0.6~3.3 V programmable output Architects of Modern Power voltage tracking product standards voltage margining compact package, horizontal: active current sharing 25.7 x 13.8 x 8.2 mm Snapshot parametric capture compact package, vertical: voltage/current/temperature monitoring 26.3 x 7.6 x 15.60 mm synchronization and phase spreading 25 A output remote differential voltage sense high efficiency programmable soft start and soft stop auto compensation fault management SMBus interface PMBus Compatible input voltage output voltage output current output wattage MODEL max max (Vdc) (Vdc) (A) (W) NDM2Z-25 4.5~14 0.6~3.3 25 82.5 PART NUMBER KEY NDM2Z-25 X - X - XXX Base Number Firmware Con guration: 000~ZZZ Module Orientation and Pin Style: HS = horizontal, surface mount HT = horizontal, through hole mount V = vertical Pin Con guration: A = Both functions present, 4.0 mm pin length (V) Example part number: NDM2Z-25V-A-001 B = Both functions present, 5.5 mm pin vertical module length (V) 4.0 mm pin length P = Power Good (H) rmware con guration 001 V = Voltage Track (H) * HS and HT modules are delivered on tape and reel * V modules are delivered in trays cui.comAdditional Resources: Product Page 3D Model CUI Inc SERIES: NDM2Z-25 DESCRIPTION: AUTO COMPENSATED, DIGITAL DC-DC POL CONVERTER date 12/21/2015 page 2 of 32 ABSOLUTE MAXIMUM RATINGS parameter conditions/description min typ max units operating temperature (see thermal consideration section) -40 125 C (T ) P1 storage temperature (T ) -40 125 C S input voltage (see operating in- formation section for input and -0.3 16 V output voltage relations)(V ) I CTRL, SA0, SA1, SALERT, SCL, SDA, VSET, SYNC, logic I/O voltage -0.3 6.5 V DDC, PG ground voltage differential -S, PREF, GND -0.3 0.3 V analog pin voltage V , +S, VTRK -0.3 6.5 V O Notes: Stress in excess of Absolute Maximum Ratings may cause permanent damage. Absolute Maximum Ratings, sometimes referred to as no destruction limits, are normally tested with one parameter at a time exceeding the limits in the Electrical Speci cation. If exposed to stress above these limits, function and performance may degrade in an unspeci ed manner. Con guration File This product is designed with a digital control circuit. The control circuit uses a con guration le which determines the functionality and performance of the product. The Electrical Speci cation table shows parameter values of functionality and performance with the default con guration le, unless otherwise speci ed. The default con guration le is designed to t most application needs with focus on high ef ciency. If different characteristics are required it is possible to change the con guration le to optimize certain performance characteristics. Note that current sharing operation requires changed con guration le. PRODUCT ELECTRICAL SPECIFICATION, HORIZONTAL T = -30 to +95 C, V = 4.5 to 14 V, V > V + 1.0 V P1 I I O Typical values given at: T = +25 C, V = 12.0 V, max I , unless otherwise speci ed under conditions. P1 I O External C = 470 F/10 m, C = 470 F/10 m. See Operating Information section for selection of capacitor types. IN OUT Sense pins are connected to the output pins. parameter conditions/description min typ max units input voltage rise time (V ) monotonic 2.4 V/ms I output voltage without 1.2 V pin-strap (V ) O output voltage adjustment 0.60 3.3 V range (V ) O output voltage adjustment see note 17 0.54 3.63 V including margining (V ) O output voltage set-point 0.025 %FS resolution (V ) O including line, load, temp see note 14 -1 1 % output voltage accuracy (V ) O current sharing operation see note 15 -2 2 % internal resistance +S/-S to 47 VOUT/GND (V ) O V = 0.6 V 2 mV O V = 1.0 V 2 mV O line regulation (V ) O V = 1.8 V 2 mV O V = 3.3 V 3 mV O V = 0.6 V 2 mV O load regulation (V ) V = 1.0 V 2 mV O O I = 0~100% V = 1.8 V 2 mV O O V = 3.3 V 3 mV O V = 0.6 V 20 mVp-p O output ripple & noise (V ) oac V = 1.0 V 30 mVp-p O C = 470 F (minimum external O V = 1.8 V 40 mVp-p O capacitance) see note 11 V = 3.3 V 60 mVp-p O cui.com