AT25PE16 16-Mbit DataFlash-L Page Erase Serial Flash Memory DATASHEET Features Single 2.3V - 3.6V supply Serial Peripheral Interface (SPI) compatible Supports SPI modes 0 and 3 Supports RapidS operation Continuous read capability through entire array Up to 85MHz Low-power read option up to 15MHz Clock-to-output time (t ) of 6ns maximum V User configurable page size 512 bytes per page (default) 528 bytes per page (customer selectable option) Two fully independent SRAM data buffers (512/528 bytes) Allows receiving data while reprogramming the main memory array Flexible programming options Byte/Page Program (1 to 512/528 bytes) directly into main memory Buffer Write Buffer to Main Memory Page Program Flexible erase options Page Erase (512/528 bytes) Block Erase (4KB) Sector Erase (128KB) Chip Erase (16-Mbits) 128-byte Security Register 128 bytes factory programmed with a unique identifier Hardware and software controlled reset options JEDEC Standard Manufacturer and Device ID Read Low-power dissipation 300nA Ultra-Deep Power-Down current (typical) 5A Deep Power-Down current (typical) 25A Standby current (typical) 7mA Active Read current (typical) Endurance: 100,000 program/erase cycles per page minimum Data retention: 20 years Complies with full industrial temperature range Green (Pb/Halide-free/RoHS compliant) packaging options 8-lead SOIC (0.150 wide and 0.208 wide) 8-pad Ultra-thin DFN (5 x 6 x 0.6mm) DS-25PE16-143C8/2018Description The Adesto AT25PE16 is a 2.3V or 2.5V minimum, serial-interface sequential access Flash memory ideally suited for a wide variety of digital voice, image, program code, and data storage applications. The AT25PE16 also supports the RapidS serial interface for applications requiring very high speed operation. Its 17,301,504 bits of memory are organized as 4,096 pages of 512 bytes (default) or 528 bytes (customer option) each. In addition to the main memory, the AT25PE16 also contains two SRAM buffers of 512/528 bytes each. The buffers allow receiving of data while a page in the main memory is being reprogrammed. Interleaving between both buffers can dramatically increase a system s ability to write a continuous data stream. In addition, the SRAM buffers can be used as additional system scratch pad memory, 2 and E PROM emulation (bit or byte alterability) can be easily handled with a self-contained three step read-modify-write operation. Unlike conventional Flash memories that are accessed randomly with multiple address lines and a parallel interface, the Adesto DataFlash-L uses a serial interface to sequentially access its data. The simple sequential access dramatically reduces active pin count, facilitates simplified hardware layout, increases system reliability, minimizes switching noise, and reduces package size. The device is optimized for use in many commercial and industrial applications where high-density, low-pin count, low-voltage, and low-power are essential. To allow for simple in-system re-programmability, the AT25PE16 does not require high input voltages for programming. The device operates from a single 2.3V to 3.6V or 2.5V to 3.6V power supply for the erase and program and read operations. The AT25PE16 is enabled through the Chip Select pin (CS) and accessed via a 3-wire interface consisting of the Serial Input (SI), Serial Output (SO), and the Serial Clock (SCK). All programming and erase cycles are self-timed. 1. Pin Configurations and Pinouts Figure 1-1. Pinouts 8-lead SOIC 8-pad UDFN Top View Top View (through package) CS 1 8 Vcc CS 1 8 Vcc SO 2 7 RESET SO 2 7 RESET WP 3 6 SCK WP 3 6 SCK GND 4 5 SI GND 4 5 SI Note: 1. The metal pad on the bottom of the UDFN package is not internally connected to a voltage potential. This pad can be a no connect or connected to GND. AT25PE16 2 DS-25PE16-143C8/2018