AT45DB161E 16-Mbit DataFlash (with Extra 512-Kbits), 2.3V or 2.5V Minimum SPI Serial Flash Memory Features Single 2.3V - 3.6V or 2.5V - 3.6V supply Serial Peripheral Interface (SPI) compatible Supports SPI modes 0 and 3 Supports RapidS operation Continuous read capability through entire array Up to 85MHz Low-power read option up to 15MHz Clock-to-output time (t ) of 6ns maximum V User configurable page size 512 bytes per page 528 bytes per page (default) Page size can be factory pre-configured for 512 bytes Two fully independent SRAM data buffers (512/528 bytes) Allows receiving data while reprogramming the main memory array Flexible programming options Byte/Page Program (1 to 512/528 bytes) directly into main memory Buffer Write Buffer to Main Memory Page Program Flexible erase options Page Erase (512/528 bytes) Block Erase (4KB) Sector Erase (128KB) Chip Erase (16-Mbits) Program and Erase Suspend/Resume Advanced hardware and software data protection features Individual sector protection Individual sector lockdown to make any sector permanently read-only 128-byte, One-Time Programmable (OTP) Security Register 64 bytes factory programmed with a unique identifier 64 bytes user programmable Hardware and software controlled reset options JEDEC Standard Manufacturer and Device ID Read Low-power dissipation 400nA Ultra-Deep Power-Down current (typical) 3A Deep Power-Down current (typical) 25A Standby current (typical) 7mA Active Read current (typical 15 MHz)) Endurance: 100,000 program/erase cycles per page minimum Data retention: 20 years Complies with full industrial temperature range Green (Pb/Halide-free/RoHS compliant) packaging options 8-lead SOIC (0.150 wide and 0.208 wide) 8-pad Ultra-thin DFN (5 x 6 x 0.6mm) 9-ball Ultra-thin UBGA (6 x 6 x 0.6mm) 11-ball Wafer Level Chip Scale Package (1) Die in Wafer Form Note: 1. Contact factory for availability. 8782KDFLASH7/2017Description The Adesto AT45DB161E is a 2.3V or 2.5V minimum, serial-interface sequential access Flash memory ideally suited for a wide variety of digital voice, image, program code, and data storage applications. The AT45DB161E also supports the RapidS serial interface for applications requiring very high speed operation. Its 17,301,504 bits of memory are organized as 4,096 pages of 512 bytes or 528 bytes each. In addition to the main memory, the AT45DB161E also contains two SRAM buffers of 512/528 bytes each. The buffers allow receiving of data while a page in the main memory is being reprogrammed. Interleaving between both buffers can dramatically increase a system s ability to write a continuous data 2 stream. In addition, the SRAM buffers can be used as additional system scratch pad memory, and E PROM emulation (bit or byte alterability) can be easily handled with a self-contained three step read-modify-write operation. Unlike conventional Flash memories that are accessed randomly with multiple address lines and a parallel interface, the Adesto DataFlash uses a serial interface to sequentially access its data. The simple sequential access dramatically reduces active pin count, facilitates simplified hardware layout, increases system reliability, minimizes switching noise, and reduces package size. The device is optimized for use in many commercial and industrial applications where high-density, low-pin count, low-voltage, and low-power are essential. To allow for simple in-system re-programmability, the AT45DB161E does not require high input voltages for programming. The device operates from a single 2.3V to 3.6V or 2.5V to 3.6V power supply for the erase and program and read operations. The AT45DB161E is enabled through the Chip Select pin (CS) and accessed via a 3-wire interface consisting of the Serial Input (SI), Serial Output (SO), and the Serial Clock (SCK). All programming and erase cycles are self-timed. 1. Pin Configurations and Pinouts Figure 1-1. Pinouts (2) (1) 8-lead SOIC 9-ball UBGA WLCSP 8-pad UDFN Bottom View Top View Top View Top View (through package) (through package) NC SI 1 8 SO SI 1 8 SO 2 7 SCK GND V SCK GND CC SI SO SCK 2 7 GND RESET 3 6 V CC RESET 3 6 V CC SCK GND CS NC WP CS 4 5 WP CS 4 5 WP V RESET CC SO SI RST CS WP NC NC Pin 1 Note: 1. The metal pad on the bottom of the UDFN package is not internally connected to a voltage potential. This pad can be a no connect or connected to GND. 2. Contact info adestotech.com for manufacturing flow and availability. AT45DB161E 2 8782KDFLASH7/2017