A product Line of Diodes Incorporated PI3A114-A LowVoltage, 4:1 Mux/Demux with Low-Swing Control Inputs Features Description CMOS Technology for Analog Applications Dio des P I3A114-A i s a o n e-t o-f o ur b idir e c t io n a l multiplier-demultiplier. Specified over a wide operating power sup- Low-swing control inputs ply voltage of 1.8 to 3.3V, the PI3A114-A oer gff ood signal linearity. Low On-Resistance e PTh I3A114-A oerff s low-swing input voltage on the EN, S1 and Wide V Range: 1.8V to 3.3V DD S0 inputs allowing the device to operate at 3.3V, and pass 3.3V Rail-to-Rail Signal Range channel data, while being controlled from a 1.8V device. Near zero propagation delay Fast Switching Speed Ultra-low quiescent power High Off Isolation: -95dB 100kHz Crosstalk Rejection Reduces Signal Distortion: -90dB 100kHz Packaging (Pb-free & Green): Block Diagram 10-contact TQFN (1.61.3) 12-contact TDFN (3.03.5) A0 A1 A2 A3 SW SW EN SW S0 SW Y A S1 SW E (1) Truth Table Enable Select Y Function EN S S 1 0 L X X Y=A , Hi-Z x H L L Y = A A A A = Hi-Z 0 1, 2, 3 Pin Configuration (top view) H L H Y = A A A A = Hi-Z 1 0, 2, 3 H H L Y = A A A A = Hi-Z 2 0, 1, 3 H H H Y = A A A A = Hi-Z 3 0, 1, 2 9 10 8 1 A0 7 Y Pin Description Pin Name Description GND 2 A3 6 A Data I/O N 3 4 5 S Select Inputs 0-1 EN Enable Y Data I/O Common GND Ground 10-pin TQFN V Power DD www.diodes.com September 2017 PI3A114-A 1 Diodes Incorporated Document Number DS40219 Rev 1-2 A2 S0 EN S1 A1 VDDA product Line of Diodes Incorporated PI3A114-A (1) (3) Absolute Maximum Ratings Recommended Operating Conditions Supply Voltage V ........................................... 0.5V to 4.2V DD Supply Voltage Operating (V ) ..........1.8V to 3.3V 5% DD Control Input Voltage (VINx) ...................................... 0V to 5V Control Input Voltage (V ) ....................0V to V IN DD (2) DC Input Voltage (V ) ............................ 0.5V to 4.2V INPUT Switch Input Voltage (V ) ............... -0.3V to V INPUT DD Continuous Current NO NC COM .............................. 300mA Operating Temperature (T ) ............... 40C to +85C A Peak Current NO NC COM Input Rise and Fall Time (t ,t ) r f (pulsed at 1ms 50% duty cycle) ............................... 400mA Control Input V = 2.3V - 3.6V ........ 0ns/V to 10ns/V DD Peak Current NO NC COM Thermal Resistance ( ) ....................... 350C/W JA (pulsed at 1ms 10% duty cycle) ............................... 500mA Storage Temperature Range (T ) .............. 65C to +150C STG Junction Temperature under Bias (T ) .............................150C J Junction Lead Temperature (T ) L (Soldering, 10 seconds) ................................................260C Power Dissipation (P ) +85C .................................. 250mW D Notes: 1. Absolute Maximum Ratings may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. 2. The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. 3. Control input must be held HIGH or LOW it must not float. DC Electrical Characteristics +1.8V Supply (V = 1.8V, T = 40C to 85C, unless otherwise noted.) DD A (2) Parameter Description Test Conditions Min. Typ. Max. Units Analog Switch Y, Ax Analog Signal Range -0.3 V V DD R On-Resistance I = 100mA, V = 0 to V 9 ON Y IN DD On-Resistance Match R I = 100mA, V = 0.5V 0.6 ON Y IN DD Between Channels R On-Resistance Flatness I = 100mA, V = 0 to V 5 ONF Y IN DD Load = 100K , V = 0.5V , Frequency = 20Hz IN DD Total Harmonic Distortion 0.03 % THD to 20KHz (1) Control Inputs V Input HIGH Voltage Guaranteed Logic HIGH Level 1.5 IH V V Input LOW Voltage Guaranteed Logic LOW Level 0.5 0.8 IL I Input HIGH Current V = Max., V = V 1 IH DD IN DD I Input LOW Current V = Max., V = GND 1 IL DD IN A High Impedance Output I 0 I , Y V 1 OZH N N DD Current V Clamp Diode Voltage V = Min., I = 18mA 1.2 V IK DD IN Notes: 1. For digital control inputs EN, S0, S1. 2. Typical values are at V = 1.8V, T = 25C ambient and maximum loading. DD A 3. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 4. Measured by the voltage drop between A and Y pin at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (I,Y) pins. www.diodes.com September 2017 PI3A114-A 2 Diodes Incorporated Document Number DS40219 Rev 1-2