PI3A223 Small Plastic Package, Dual SPDT Analog Switch Features Description Block Diagram Applications Pin Description Pin Name Description 1 V Positive Power Supply DD Pin Configuration (Top view) 2 NO1 Data Port (Normally open) 3 COM1 Common Output / Data Port 4 IN1 Logic Control 5 NC1 Data Port (Normally closed) 6 GND Ground 7 NC2 Data Port (Normally closed) 8 IN2 Logic Control 9 COM2 Common Output / Data Port 10 NO2 Data Port (Normally open) Function Table Logic Input (IN ) Function X 0 NC Connected to COM X X 1 NO Connected to COM X X Note: x = 1 or 2 PI3A223 www.diodes.com April 2018 Document Number DS40948 Rev 1-2 1 Diodes Incorporated PI3A223 Maximum Ratings Note: Storage Temperature.. -65 to +150 Stresses greater than those listed under MAXIMUM Ambient Temperature with Power Applied......................-40 to +85 RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the Supply Voltage V -0.5Vto +4.6V DD device at these or any other conditions above those Control Input Voltage V .0Vto +4.6V INx indicated in the operational sections of this specification DC Input Voltage V -0.5Vto +4.6V INPUT is not implied. Exposure to absolute maximum rating Continuous Current NO NC COM ..300mA conditions for extended periods may affect reliability. Peak Current NO NC COM The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are (pulsed at 1ms 50% duty cycle) ... 400mA observed. Peak Current NO NC COM Control input must be held HIGH or LOW it must not (pulsed at 1ms 10% duty cycle) ... 500mA float. ESD(HBM) .4kV Recommended Operating Conditions Symbol Parameter Conditions Min. Typ. Max. Unit V Operating Voltage - 1.8 - 4.2 V DD V Control Input Voltage - 0 - V V IN DD V Switch Input Voltage - -0.3 - 4.2 V INPUT T Operating Temperature - -40 25 85 C A t , t Input Rise and Fall Time - 0 - 10 ns/V r f DC Electrical Characteristics +3.0V Supply (V = 2.7V to 3.6V, V =+1.6V, V =+0.4V, T = 40C to 85C, unless otherwise noted. Typical values are at DD IH IL A 3.0V and +25C.) Parameter Symbol Test Conditions TEMP Min. Typ. Max. Units ANALOG SWITCH V , V , NO NC Analog Signal Range - -40 C to 85 C 0 - V V DD V COM - 0.55 0.9 +25C V = 2.7V, I = 100mA, V or DD COM NO On-Resistance R ON V =1V, Test Circuit 1 - 0.55 1 NC -40 C to 85 C - 0.05 0.22 On-Resistance Match R V = 2.7V, I = 100mA, V or +25C ON DD COM NO Between Channels V =1V, Test Circuit 1 - 0.05 0.25 NC -40 C to 85 C - 0.1 0.22 On-Resistance R V = 2.7V, I = 100mA, V or +25C ONF DD COM NO Flatness V = 1V, 2.5V, Test Circuit 1 NC -40 C to 85 C - 0.1 0.26 Source Off I or V =3.6V, V or V = OFF (NO) DD NO NC -40 C to 85 C - - 1 Leakage Current I 3.3V/0.3V, V = 0.3V/3.3V OFF (NC) COM A I , NC(ON) Channel On Leakage V = 3.6V, V or V = 3V/ DD NO NC I , I -40 C to 85 C - - 1 NO(ON) COM Current 0.3V, V = 3V/0.3V, or floating COM (ON) DIGITAL INPUTS Input Logic High V - 1.2 - - -40 C to 85 C IH V Input Logic Low V - - 0.5 - -40 C to 85 C IL IN Input Leakage A I V = 2.7V, V =0 or 2.7V -40 C to 85 C - - 1 IN DD IN Current DYNAMIC CHARACTERISTICS V =1.5V, V =0V, IH IL Turn-On Time t +25C - 16 - ns ON See Test Circuit Figure 2. V =1.5V, V =0V, IH IL Turn-Off Time t +25C - 60 - ns OFF See Test Circuit Figure 2. Break-Before-Make t V =1.5V, V =0V, +25C - 10 - ns D IH IL PI3A223 www.diodes.com April 2018 Document Number DS40948 Rev 1-2 2 Diodes Incorporated