PI3CH281 2-Channel 4:1 Mux/DeMux, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug Features Description Pin Description Pin No Pin Name Description 1111111 1 Enable EN 2, 14 S , S Select Input 1 0 3, 4, 5, 6 A , A A A Data Outputs I 3 I 2, I 1, I 0 7, 9 Y , Y Data Outputs A B 8 GND Ground 10, 11, 12, B , B B B Data Outputs Pin Configuration I 0 I 1, I 2, I 3 13 1111111 15 Not connected NC 16 V Power CC (1) Truth Table Enable Select S Y Function EN S 0 1 X Hi-Z Disable H X L I0 S =0 1-0 L L H I1 S =1 L L 1-0 L I2 S =2 L H 1-0 Block Diagram H I3 S =3 L H 1-0 Note: 1. H=High Voltage Level L=Low Voltage Level PI3CH281 www.diodes.com April 2018 Document Number DS40893 Rev 1-2 Diodes Incorporated 1 PI3CH281 Maximum Ratings Note: o o Storage Temperature ................................................................................... -65 C to +150 C Stresses greater than those listed under MAXIMUM Ambient Temperature with Power Applied........................................ 40C to +85C RATINGS may cause permanent damage to the device. This is a stress rating only and functional Supply Voltage to Ground Potential ............................................................ -0.5V to + 4.6V operation of the device at these or any other condi- DC Input Voltage ............................................................................................ -0.5V to + 6.0V tions above those indicated in the operational sec- DC Output Current .......................................................................................... 120mA tions of this specification is not implied. Exposure Power Dissipation .............................................................................................................. 0.5W to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics 3.3V supply (Over operating range, T = -40 ~ +85C, V =3.3V10%, unless otherwise noted) A CC (1) (2) Symbol Description Test Conditions Min Typ Max Unit V Control Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 - - V IH V Control Input LOW Voltage Guaranteed Logic LOW Level -0.5 - 0.8 V IL V Clamp Diode Voltage V = Min., I = -18mA - -1.3 -1.8 V IK CC IN I Input HIGH Current V = Max., V = V - - 1 A IH CC IN CC I Input Low Current V = Max., V = GND - - 1 A IL CC IN (3) I High-Impedance Current 0 Y, In V - - 1 A OZH CC V = Min., V = 0.0V CC IN - 4 6 I = -48mA or -64mA (4) ON R Switch On-Resistance ON V = Min., V = 3.6V CC IN - 5 8 I = -15mA ON Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at V = 3.3V, TA = 25C ambient and maximum loading. CC 3. Measured by the voltage drop between Y and In pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (Y, In) pins. 2.5V supply (Over operating range, T = -40 ~ +85C, V =2.5V10%, unless otherwise noted) A CC (1) (2) Symbol Description Test Conditions Min Typ Max Unit V Control Input HIGH Voltage Guaranteed Logic HIGH Level 1.8 - V +0.3 V IH CC V Control Input LOW Voltage Guaranteed Logic LOW Level -0.3 - 0.8 V IL V Clamp Diode Voltage V = Max., I = -6mA - -0.7 -1.8 V IK CC IN I Input HIGH Current V = Max., V = V - - 1 A IH CC IN CC I Input Low Current V = Max., V = GND - - 1 A IL CC IN (3) I High-Impedance Current 0 Y, In V - - 1 A OZH CC V = Min., V = 0.0V CC IN - 4 8 I = -48mA (4) ON R Switch On-Resistance ON V = Min., V = 2.25V CC IN - 7 14 I = -15mA ON Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at V = 2.5V, TA = 25C ambient and maximum loading. CC 3. Measured by the voltage drop between Y and In pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (Y, In) pins. PI3CH281 www.diodes.com April 2018 Document Number DS40893 Rev 1-2 Diodes Incorporated 2