PI3CH480 4-Channel 2:1 Mux/DeMux, Enable Low 1.8V / 2.5V / 3.3V, High-Bandwidth, Hot Plug Features Description Pin Configuration Block Diagram TSSOP/QSOP Top View Truth Table UQFN3x3-16 Top View EN Function S YA YB YC YD Disable H X Hi-Z Hi-Z Hi-Z Hi-Z S=0 L L IA0 IB0 IC0 ID0 S=1 L H IA1 IB1 IC1 ID1 Note: H=High Voltage Level L=Low Voltage Level Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS), 2011/65/EU (RoHS 2) & 2015/863/EU (RoHS 3) compliant. 2. See PI3CH480 Pin Description Pin No of Pin No of TSSOP UQFN3x3- Pin Name Description QSOP 16 1 15 S Select Inputs 2, 3, 5, 6, 16,1,3,4, A , A B , B I 0 I 1, I 0 I 1, Data Inputs 11,10,14,13 9,8,12,11 C , C D , D I 0 I 1, I 0 I 1 4, 7, 9, 12 2,5,7,10 Y , Y , Y , Y Data Outputs A B C D 8 6 GND Ground 1111111 EN 15 13 Enable 16 14 V Power CC Center Pad GND Maximum Ratings Note: Storage Temperature .................................................................................... -65C to +150C Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. Ambient Temperature with Power Applied........................................ 40C to +85C This is a stress rating only and functional operation of the Supply Voltage to Ground Potential ............................................................ -0.5V to + 4.6V device at these or any other conditions above those DC Input Voltage ............................................................................................ -0.5V to + 6.0V indicated in the operational sections of this specification DC Output Current .......................................................................................... 120mA is not implied. Exposure to absolute maximum rating Power Dissipation .............................................................................................................. 0.5W conditions for extended periods may affect reliability. DC Electrical Characteristics 3.3V Supply (Over Operating Range, T = -40C ~ +85C, V = 3.3V 10%, unless otherwise noted) A CC (1) (2) Symbol Description Test Conditions Min Typ Max Unit V Control Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 V IH V Control Input LOW Voltage Guaranteed Logic LOW Level -0.5 0.8 V IL V Clamp Diode Voltage V = Min., I = -18mA -1.3 -1.8 V IK CC IN I Input HIGH Current V = Max., V = V 1 A IH CC IN CC I Input Low Current V = Max., V = GND 1 A IL CC IN (3) I High-Impedance Current 0 Y, In V 1 A OZH CC V = Min., V = 0.0V CC IN 4 6 I = -48mA or -64mA (4) ON R Switch On-Resistance ON V = Min., V = 3.6V CC IN 5 8 I = -15mA ON Notes: 1. For maximum or minimum conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at V = 3.3V, TA = 25C ambient and maximum loading. CC 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between Y and In pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (Y, In) pins. PI3CH480 www.diodes.com November 2018 Document Number DS40329 Rev 3-2 2 Diodes Incorporated