A product Line of Diodes Incorporated PI5L200 Precision Wide Bandwidth LanSwitch Quad 2:1 Mux/DeMux Features Description Single 3.3V/5V supply operation Diodes PI5L200 is a Rail-to-Rail Quad 2:1 multiplexer/demulti- Rail-To-Rail Operation plexer LanSwitch with 3-state outputs. The On-Resistance typi- Very Low Distortion: 2% cally varies from 5 ohms to 7 ohms with data inputs of 0V to 5V. Replaces mechanical relays Generally, this part can be used to replace mechanical relays in High-performance, low-cost solution for switching between low voltage (3.3V/5V systems) LAN applications. different LAN signals With a wide bandwidth of 135 MHz, the PI5L200 can switch Fast Low crosstalk: 70dB 30 Mbps Ethernet and ATM25 signals. Into 100-ohm UTP cables, the Low insertion loss and On-Resistance: 6-ohms typical switch distortion is typically less than two percent. Crosstalk 30 Off isolation: 55dB 30 Mbps MHz is 70dB. The PI5L200 operates from a single 3.3V/5V sup- Wide bandwidth data rates >135 Mbps ply and interface to TTL logic. Low Quiescent Supply Current (100nA typical) Packaging (Pb-free & Green available): Pin Configuration 16-pin 150-mil wide plastic QSOP (Q) 16-pin 150-mil wide plastic SOIC (W) S 1 16 VCC 16-pin 173-mil wide plastic TSSOP (L) IA0 2 15 E Applications 3 14 IA1 ID0 4 13 YA ID1 10/100 Base-TX/T4 IB0 5 12 YD 100VG-AnyLAN IB1 6 11 IC0 Token Ring 4/16 Mbps 7 10 ATM25 YB IC1 NIC Adapter and Hubs 8 9 GND YC SONET OCI 51.8Mbps T1/E1 Block Diagram Pin Description Pin Name Description IA0 YA IAn-IDn Data Inputs IA1 S Select Inputs IB0 E Enable YB IB1 YA-YD Data Outputs GND Ground IC0 YC V Power CC IC1 Truth Table ID0 YD E S YA YB YC YD Function ID1 H X Hi-Z Hi-Z Hi-Z Hi-Z Disable L L A B C D S = 0 I 0 I 0 I 0 I 0 L H A B C D S = 1 I 1 I 1 I 1 I 1 Decoder/Driver Note: H = High Voltage Level, S E L = Low Voltage Level, S witches are shown with logic0 input (Select and Enable) www.diodes.com January 2018 PI5L200 1 Diodes Incorporated Document Number DS40562 Rev 1-2 A product Line of Diodes Incorporated PI5L200 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Note: Storage Temperature .......................................................... 65C to +150C Stresses greater than those listed under MAXIMUM RAT- INGS may cause permanent damage to the device. This is a Ambient Temperature with Power Applied ......................... 40C to +85C stress rating only and functional operation of the device at Supply Voltage to Ground Potential ..................................... 0.5V to +7.0V these or any other conditions above those indicated in the DC Input Voltage ........................................................... 0.5V to V +0.5V operational sections of this specification is not implied. Ex- CC posure to absolute maximum rating conditions for extended DC Output Current ............................................................................ 120 mA periods may affect reliability. Power Dissipation ................................................................................. 0.5W Single 5.0V Supply DC Electrical Characteristics (Over the Operating Range, T = -40C to +85C, V = 5V 10%, GND = 0V) A CC (1) (2) Parameters Description Test Conditions Min. Typ. Max. Units V Analog Signal Range 0 - V V ANALOG CC R ON-Resistance I = 10mA to 30mA - 6 12 ON ON R Match Between Channels - 0.4 2 ON R R Flatness I = 1mA, V , V = 0V to 5V - 3 5 FLAT(ON) ON ON NO NC I I On/Off Leakage Current V , V = 4.5V 100 - 100 nA NO(OFF), NO(ON) NO NC I Quiescent Supply Current V = 5.5V, V = 0V or V - - 1 A CC CC IN CC I Output Current V , V or V = 0V to 5V 100 - - mA O NO NC COM V Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 - - IH V V Input LOW Voltage Guaranteed Logic LOW Level 0.5 - 0.8 IL I Input HIGH Current V = Max., V = V - - 1 IH CC IN CC A I Input LOW Current V = Max., V = GND - - 1 IL CC IN Dynamic Electrical Characteristics (Over the Operating Range, T = -40C to +85C, V = 5V 10%, GND = 0V) A CC (1) (2) Parameters Description Test Conditions Min. Typ. Max. Units t Turn-on Time V or V = 3.0V, see Fig. 2 - 10 20 ON ON NC ns t Turn-off Time V or V = 3.0V, see Fig. 2 - 5 10 OFF ON NC - 70 - X Crosstalk R = 100 ohms, f = 30 MHz, see Fig. 4 dB TALK L C NC or NO Capacitance f = 1 kHz - 13 - pF (OFF) O Off Isolation R = 100 ohms, f = 30 MHz, see Fig. 5 - 55 - dB IRR L BW Bandwidth -3dB R = 100 ohms, see Fig. 3 - 137 - MHz L D Distortion DR /RL R = 100 ohms - 2 - % ON L Note: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for applicable device type. 2. Guaranteed by design. www.diodes.com January 2018 PI5L200 2 Diodes Incorporated Document Number DS40562 Rev 1-2