PI5L200 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 1 2345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012 12345678901 2 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 Precision Wide Bandwidth LanSwitch Quad 2:1 Mux/DeMux Features Description Single 3.3V/5V supply operation Pericom Semiconductors PI5L200 is a Rail-to-Rail Quad 2:1 multiplexer/demultiplexer LanSwitch with 3-state outputs. The On- Rail-To-Rail Operation Resistance typically varies from 5 ohms to 7 ohms with data inputs Very Low Distortion: 2% of 0V to 5V. Generally, this part can be used to replace mechanical Replaces mechanical relays relays in low voltage (3.3V/5V systems) LAN applications. High-performance, low-cost solution for switching With a wide bandwidth of 135 MHz, the PI5L200 can switch Fast between different LAN signals Ethernet and ATM25 signals. Into 100-ohm UTP cables, the switch Low crosstalk: 70dB 30 Mbps distortion is typically less than two percent. Crosstalk 30 MHz is Low insertion loss and On-Resistance: 6-ohms typical 70dB. The PI5L200 operates from a single 3.3V/5V supply and Off isolation: 55dB 30 Mbps interface to TTL logic. Wide bandwidth data rates >135 Mbps Applications Low Quiescent Supply Current (100nA typical) 10/100 Base-TX/T4 Packaging (Pb-free & Green available): 100VG-AnyLAN 16-pin 150-mil wide plastic SOIC (W) Token Ring 4/16 Mbps 16-pin 150-mil wide plastic QSOP (Q) ATM25 16-pin 173-mil wide plastic TSSOP (L) NIC Adapter and Hubs SONET OCI 51.8Mbps Block Diagram T1/E1 IA0 YA IA1 IB0 Pin Configuration YB IB1 IC0 YC S 16 1 V CC IC1 1A0 2 15 E ID0 1A1 3 14 1D0 YD ID1 YA 13 4 1D1 1Bo 5 12 YD 1B1 6 11 1C0 DECODER/DRIVER YB 7 10 1C1 GND 8 9 YC ES (1) Pin Description Truth Table ES YBA YCYDYnFunctio Pnin Name Descriptio HXHZi-ZHZi- HZi-Hei- Disabl IsAn-IDn Data Input LL I0A0I0B I0CI0D S = SsSelect Input LH I1A1I1B I1CI1D S = EeEnabl Note: YsA-YD Data Output 1. H = High Voltage Level GdND Groun L = Low Voltage Level Switches are shown with logic0 input (Select and Enable) V Power CC PS7055G 10/01/04 1PI5L200 Precision Wide Bandwidth LanSwitch 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 Quad 2:1 Mux/DeMux2123456789012 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Note: Storage Temperature ............................................................ 65C to +150C Stresses greater than those listed under MAXIMUM RAT- INGS may cause permanent damage to the device. This is a Ambient Temperature with Power Applied ........................... 40C to +85C stress rating only and functional operation of the device at these or any other conditions above those indicated in the Supply Voltage to Ground Potential ....................................... 0.5V to +7.0V operational sections of this specification is not implied. DC Input Voltage ............................................................. 0.5V to V +0.5V Exposure to absolute maximum rating conditions for ex- CC tended periods may affect reliability. DC Output Current .............................................................................. 120mA Power Dissipation ................................................................................. 0.5W Single 5.0V Supply DC Electrical Characteristics (Over the Operating Range, T = 40C to +85C, V = 5V 10%, GND = 0V) A CC (1) (2) PnarametersDsescriptio Test Condition M.in. TypMsax. Unit VA0nalog Signal Range V V ANALOG CC ROIN-Resistance =10mA to 30mA 6 12 ON ON RMatch Between Channels 02.4 ON R RFIlatness = 1mA, V , V=0V to 5V 35 FLAT(ON) ON ON NO NC I , IOVn/Off Leakage Current , V=04.5V 10 1A00 n NO(OFF) NO(ON) NO NC IQVuiescent Supply Current = 5.5V, V = 0V or V 1 A CC CC IN CC IOVutput Current , V or V=00V to 5V 10 mA O NO NC COM VIlnput HIGH VoltageG0uaranteed Logic HIGH Leve 2. IH V VIlnput LOW VoltageG5uaranteed Logic LOW Leve 0. 0.8 IL IIVnput HIGH Current = Max., V = V 1 IH CC IN CC A IIVnput LOW Current = Max., V=GND 1 IL CC IN Dynamic Electrical Characteristics (Over the Operating Range, T = 40C to +85C, V = 5V 10%, GND = 0V) A CC (1) (2) PnarametersDsescriptio Test Condition M.in. TypMsax. Unit tTVurn-on Time or V=3.0V, see Figure 2 100 2 ON NO NC ns tTVurn-off Time or V=3.0V, see Figure 2 5 10 OFF NO NC XCRrosstalk =100 ohms, f = 30 MHz, see Figure 4 70 dB TALK L CNzC or NO Capacitancef= 1kH 13 pF (OFF) OORff Isolation =100 ohms, f = 30 MHz, see Figure 5 55 dB IRR L BBWBRandwidth 3 d=100 ohms, see Figure 3 137 MHz L DRDistortion D ON/RRL=100 ohms 2% L Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for applicable device type. 2. Guaranteed by design. PS7055G 10/01/04 2