PI5USB30213XEAEX Diodes Incorporated

PRELIMINARY INFORMATION COMPANY CONFIDENTIAL PI5USB30213 2 USB 3.0/3.1 Gen 1 SuperSpeed Mux/Demux Switch with I C Control for Type-C Connector Features Description USB Type-C Specification 1.1 The PI5USB30213 is a dual differential channel bi-directional multiplexer/de-multiplexer switch solution for USB 3.0/31 Dual Differential Channel, 2:1 USB 3.0/31 GEN 1 GEN 1 Type-C connector applications. Mux/DeMux PI5USB30213 switches between the USB controller and the Switches USB controller and Type-C connector new Type-C connector. It supports host mode, device mode Supports Host-mode/Device-mode/Dual-role mode and dual-role mode ports with automatic configuration based Auto-configure ports orientation through CC detection on the voltage levels detected on CC pin. It offers excellent signal integrity for high-speed signals at low power Supports VCONN to power active cables and other dissipation. accessories Supports over-current protection and over-voltage 2 PI5USB30213 supports both pin and I C control base on protection for VCONN ADDR pin setting. In pin control mode, the PORT input pin 2 Allow both pin control and I C interface determines the port setting, whether this is a host, device or dual-role port. In host mode, the system can monitor ID pin to Integrated power switches, high-precision resistors and know the connector status while default current mode is set. current sources for CC pins Systems running in device mode can monitor system VBUS Provides support for default current, 1.5A and 3A for connector status as well as OUT1 and OUT2 pins for host s 2 modes with I C control charging profile capability. Output indicator for plug-in detection 2 Enabling I C control mode allow high flexibility for port Power saving mode control and communications through registers read/write in Wide power supply range : 2.7V 5.5V PI5USB30213. There is also flexibility to support Default, o o Temperature Range: -40 C to 85 C 1.5A and 3A current modes. An interrupt signal for indicating 2 Packaging (Pb-free & Green): changes with the I C registers is sent to the master to notify the system any change in the Type-C connector while in 24- contact, X1QFN(2mm x 4mm) parallel the system can still monitor ID pin. Applications Block Diagram Notebooks Mobile Phones Tablets Docking Station Pin Configuration Figure 2. PI5USB30213 Block diagram Figure 1. Pin Assignment (Top View) PI5USB30213 www.diodes.com 12/1/2017 Datasheet Number DS40461 Rev 1-2 Diodes Incororated All trademarks are property of their respectiv e owners. 1 PRELIMINARY INFORMATION COMPANY CONFIDENTIAL PI5USB30213 Pin Descriptions Pin Number Pin Name I/O Description 2 I C communication clock signal. Dual function as open drain Type-C Current Mode Detect 1 in pin control mode when port is a device 1 SCL/OUT2 I/O OUT2 OUT1 Current Mode Hi-Z Hi-Z Default Hi-Z Low Medium Low Low High 2 Open drain output. In I C control mode, this is an active LOW interrupt 2 signal for indicating changes in I C registers. 2 INTB/OUT3 O Dual function as analog audio adapter detection in pin control mode: OUT3=Hi-Z Not detected OUT3=Low Analog audio adapter detected Tri-level input pin to indicate port mode (for pin control only): PORT is floating Try.SNK Dual Role (DRP) 3 PORT I PORT=VDD Host (SRC) PORT=GND Device (SNK) 4 Ap I/O Differential USB 3.0/31 GEN 1 signal A (PHY side) 5 An I/O Differential USB 3.0/31 GEN 1 signal A (PHY side) 6 VDD Power Positive supply voltage from VBAT 7 Bn I/O Differential USB 3.0/31 GEN 1 signal B (PHY side) 8 Bp I/O Differential USB 3.0/31 GEN 1 signal B (PHY side) Open drain output. Asserted low when CC pin detected device 9 ID O attachment when port is a Host (or dual-role acting as Host), otherwise ID is hi-z. 10 VCONN Power Supply voltage for VCONN 11 CC1 I/O Type-C Configuration channel signals 12 CC2 I/O Type-C Configuration channel signals Active-low enable input pin (with internal weak pull up) 13 ENB I ENB=VDD Disabled/Low Power State ENB=GND Enabled/Active State 14 B1p I/O Differential USB 3.0/31 GEN 1 signal B for position 1 connection 15 B1n I/O Differential USB 3.0/31 GEN 1 signal B for position 1 connection 16 A1p I/O Differential USB 3.0/31 GEN 1 signal A for position 1 connection 17 A1n I/O Differential USB 3.0/31 GEN 1 signal A for position 1 connection 18 B2n I/O Differential USB 3.0/31 GEN 1 signal B for position 2 connection 19 B2p I/O Differential USB 3.0/31 GEN 1 signal B for position 2 connection 20 A2n I/O Differential USB 3.0/31 GEN 1 signal A for position 2 connection 21 A2p I/O Differential USB 3.0/31 GEN 1 signal A for position 2 connection 2 Tri-level input pin to indicate I C address or pin control mode: ADDR is floating Pin control mode 22 ADDR I 2 ADDR=VDD I C enabled with ADDR bit 6 equal to 1 2 ADDR=GND I C enabled with ADDR bit 6 equal to 0 23 VBUSDET I VBUS detection 2 I C communication data signal. Dual function as open drain Type-C Current Mode Detect 1 in pin control mode when port is a device 24 SDA/OUT1 I/O OUT2 OUT1 Current Mode Hi-Z Hi-Z Default Hi-Z Low Medium Low Low High Thermal Pad GND Ground Ground PI5USB30213 www.diodes.com 12/1/2017 Datasheet Number DS40461 Rev 1-2 Diodes Incororated All trademarks are property of their respectiv e owners. 2