PI5V330A Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Features: Description: High-performance solution to switch between video sources Pericom Semiconductors PI5V330A is a true bi di rec tion al Quad Wide bandwidth: >360 MHz 2-channel multiplexer/demultiplexer that is rec om mend ed for both RGB and com pos ite video switching applications. The Low On-Resistance: 3 Video Switch can be driven from a current output RAMDAC or Low crosstalk at 10 MHz: 58dB voltage output com pos ite video source. Ultra-low quiescent power (0.1A typical) Low On-Resistance and wide bandwidth make it ideal for video Single supply operation: +5.0V and other applications. Also this device has ex cep tion al ly high Fast switching: 10ns current capability which is far greater than most analog switches High-current output: 100mA offered today. A single 5V supply is all that is required for opera- Packaging (Pb-free & Green available): tion. 16-pin 150-mil wide plastic SOIC (W) The PI5V330A offers a high-performance, low-cost so lu tion to 16-pin 150-mil wide plastic QSOP (Q) switch between video sources. The application section de scribes the PI5V330A replacing the HC4053 multiplier and buffer/ ampli er. Block Diagram Pin Diagram 1 S A D A 2 S A IN 1 16 V CC 1 S B 1 S A 2 15 D B EN 2 S B 2 S A 1 3 14 S D 1 S C D A 2 4 13 S D D C 2 S C 1 S B D 5 12 D 1 S D 2 1 S B S C 6 11 D D 2 S D D 2 B S C 7 10 D DECODER/DRIVERS D GND 8 9 EN IN Pin Description Truth Table Pin Name Description EN IN ON Switch 1 , 1 , 1 , S1 00 1 , 1 , 1 , 1 S A S B S C S D S A S B S C D, Analog Video I/O 2 , 2 , 2 , S2 S A S B S C D 01 2 , 2 , 2 , 2 S A S B S C S D IN Select Input 1 X Disabled EN Enable D , D , D , D Analog Video I/O A B C D GND Ground V Power CC PS8695C 02/22/08 1 08-0288PI5V330A Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ..........................................................65C to +150C Note: Stresses greater than those listed under MAX I MUM RAT- Ambient Temperature with Power Applied .........................40C to +85C INGS may cause permanent damage to the de vice. This is Supply Voltage to Ground Potential (Inputs & V Only) ...0.5V to +7.0V CC a stress rating only and func tion al op er a tion of the device at these or any other conditions above those indicated in the Supply Voltage to Ground Potential (Outputs & D/O Only) 0.5V to +7.0V operational sections of this speci cation is not implied. Ex- DC Input Voltage ..................................................................0.5V to +7.0V posure to absolute maximum rating conditions for extended DC Output Current .............................................................................120mA periods may affect reliability. Power Dissipation .................................................................................0.5W DC Electrical Characteristics (Over the Operating Range, T = 40C to +85C, V = 5V 5%) A CC (1) (2) Parameters Description Test Conditions Min. Typ. Max. Units V Analog Signal Range 0 2.0 ANALOG V V Input HIGH Voltage Guaranteed Logic HIGH level 2.0 IH V Input LOW Voltage Guaranteed Logic LOW Level -0.5 0.8 IL I Input HIGH Current V = Max., V = V 1 IH CC IN CC I Input LOW Current V = Max., V = GND 1 IL CC IN A Analog Output I 0 S1, S2, or D V , Switch OFF 1 O CC Leakage Currnet V Clamp Diode Voltage V = Min., I = -18mA -0.7 -1.2 V IK CC IN (3) I Short Circuit Current 150 mA OS Input Hysteresis at V V = MIN., V = 1.0V R = 75, I = 13 mA 3 7 mV H CC IN L ON Control Pins R Switch On-Resistance V = MIN., V = 2.0V R = 75, I = 26 mA 3 7 10 ON CC IN L ON Notes: 1. For Max. or Min. conditions, use appropriate value speci ed under Electrical Characteristics for the applicable device type. 2. Typical values are at V = 5.0V, TA = 25C ambient and maximum loading. CC 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between S1, S2, and D I/O pins at indicated current through the switch. On-Resistance is de ter mined by the lower of the voltages on the S1, S2, and D I/O pins. PS8695A 02/22/08 2 08-0288