PI5V330 Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Features Description High-performance solution to switch between video sources Pericom Semiconductor s PI5V330 is a true bidirectional Quad 2-channel multiplexer/demultiplexer recommended for both Wide bandwidth: 400 MHz (typical) RGB and composite video switching applications. The video Low On-Resistance: 5 (typical) switch can be driven from a current output RAMDAC or voltage Low crosstalk at 10 MHz: 56dB output composite video source. Ultra-low quiescent power (0.1A typical) Low On-Resistance and wide bandwidth make it ideal for video Single supply operation: +5.0V and other applications. Also this device has exceptionally high Packaging (Pb-free & Green Available): current capability which is far greater than most analog switches 16-pin 150-mil wide plastic SOIC (W) offered today. A single 5V supply is all that is required for opera- 16-pin 150-mil wide plastic QSOP (Q) tion. The PI5V330 offers a high-performance, low-cost solution to switch between video sources. The application section describes the PI5V330 replacing the HC4053 multiplier and buffer/ amplifier. Block Diagram Pin Configuration Pin Description Pin Name Description 1 , 1 , 1 , 1 S A S B S C S D Analog Video I/O 2 , 2 , 2 , 2 S A S B S C S D IN Select Input Truth Table EN Enable EN IN ON Switch D , D A B Analog Video I/O 0 0 1 , 1 , 1 , 1 D , D S A S B S C S D C D 0 1 2 , 2 , S2 , 2 GND Ground S A S B C S D 1 X Disabled V Power CC PS7032I 1/14/13 1 13-0017PI5V330 Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature .......................................................... 65C to +150C Note: Stresses greater than those listed under MAXIMUM RAT- Ambient Temperature with Power Applied ......................... 40C to +85C INGS may cause permanent damage to the device. This is Supply Voltage to Ground Potential (Inputs & V Only) ...0.5V to +7.0V CC a stress rating only and functional operation of the device at these or any other conditions above those indicated in the Supply Voltage to Ground Potential (Outputs & D/O Only) 0.5V to +7.0V operational sections of this specification is not implied. Ex- DC Input Voltage ..................................................................0.5V to +7.0V posure to absolute maximum rating conditions for extended DC Output Current ............................................................................. 120mA periods may affect reliability. Power Dissipation ................................................................................. 0.5W DC Electrical Characteristics (Over the Operating Range, TA = 40C to +85C, VCC = 5V 5%) (1) (2) Parameters Description Test Conditions Min. Typ. Max. Units V Analog Signal Range 0 2.0 ANALOG V Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 V IH V Input LOW Voltage Guaranteed Logic LOW Level 0.5 0.8 IL I Input HIGH Current V = Max., V = V 1 IH CC IN CC I Input LOW Current V = Max., V = GND 1 A IL CC IN I Analog Output Leakage Current 0 S1, S2 or D V , Switch OFF 1 O CC V Clamp Diode Voltage V = Min., I = -18mA -0.7 -1.2 V IK CC IN V Input Hysteresis at Control Pins 150 mV H V = Min., V = 1.0V, CC IN 5 7 I = 13mA ON (3) R Switch On-Resistance ON V = Min., V = 2.0V, CC IN 7 10 I = 26mA ON Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at V = 5.0V, T = 25C ambient and maximum loading. CC A 3. Measured by the voltage drop between S1, S2, and D I/O pins at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the S1, S2, and D I/O pins. PS7032I 01/14/13 2 13-0017