REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 02. Add vendor CAGE 27014 and 75569. Add logic diagram. 91-04-11 M. A. Frye Technical and editorial changes throughout. B Changes in accordance with notice of revision 5962-R190-92. - jak 92-06-19 Tim H. Noh C Redraw the switching waveforms in figure 4, switching waveforms and test 06-07-11 Thomas M. Hess circuit. Update the boilerplate to current requirements as specified in MIL-PRF-38535. Editorial changes throughout. jak D Add footnote 4/ to I test in table I. jak 10-01-06 Thomas M. Hess CC REV SHEET REV SHEET REV STATUS REV D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Marcia B. Kelleher DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-88639 01 R A Drawing number Device type Case outline Lead finish (see 1.2.1) (see 1.2.2) (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54FCT573 Octal transparent latch with three-state outputs, TTL compatible 02 54FCT573A Octal transparent latch with three-state outputs, TTL compatible 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. 1/ Supply voltage range (V ) ........................................................................... -0.5 V dc to +7.0 V dc CC DC input voltage range (V ) 2/ .................................................................... -0.5 V dc to V + 0.5 V dc IN CC DC output voltage range (V ) 2/ ............................................................... -0.5 V dc to V + 0.5 V dc OUT CC DC input diode current (I ) ........................................................................... -20 mA IK DC output diode current (I ) ........................................................................ -50 mA OK DC output current (I ) ................................................................................ 100 mA OUT Maximum power dissipation (P ) 3/ ............................................................. 500 mW D Thermal resistance, junction-to-case ( ) .................................................... See MIL-STD-1835 JC Storage temperature range (T ) ................................................................ -65C to +150 C STG Junction temperature (T ) ............................................................................. +175C J Lead temperature (soldering, 10 seconds) ................................................... +300C 1.4 Recommended operating conditions. Supply voltage range (V ) ........................................................................... +4.5 V dc to +5.5 V dc CC Maximum low level input voltage (V )........................................................... 0.8 V dc IL Minimum high level input voltage (V ) .......................................................... 2.0 V dc IH Case operating temperature range (T ) ........................................................ -55C to +125 C C Minimum setup time, high or low (Dn to LE) (t ) ............................................ 2.0 ns s Minimum hold time, high or low (Dn to LE) (t ).............................................. 1.5 ns h Minimum LE pulse width, high or low (t ) ...................................................... 6.0 ns w 1/ Unless other wise specified, all voltages are referenced to ground. 2/ For V > 6.5 V dc, the upper bound is limited to V . CC CC 3/ Must withstand the added P due to short circuit test, e.g., I . D OS SIZE STANDARD 5962-88639 A MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS REVISION LEVEL SHEET COLUMBUS, OHIO 43218-3990 D 2 DSCC FORM 2234 APR 97