REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add vendor CAGE 75569. Technical changes throughout. - mbk 92-02-10 M. A. Frye Update the boilerplate to the current requirements of MIL-PRF-38535. B 07-12-17 Thomas M. Hess - JAK Correct test condition for total power supply current (I ) and add CC C footnote 6/ in table I. Update boilerplate paragraphs to current 10-08-11 Thomas M. Hess MIL-PRF-38535 requirements. MAA. REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Monica L. Poelking DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 STANDARD CHECKED BY 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89730 01 K A Drawing number Device type Case outline Lead finish (see 1.2.1) (see 1.2.2) (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54FCT543 8-bit octal latched transceiver, non-inverting, with three-state outputs, TTL compatible 02 54FCT543A 8-bit octal latched transceiver, non-inverting, with three-state outputs, TTL compatible 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style K GDIP1-T24 or CDIP2-T24 24 Dual-in-line L GDFP1-F24 or CDFP2-F24 24 Flat pack 3 CQCC1-N28 28 Square leadless chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. 1/ Supply voltage range (V ) ..................................................................... -0.5 V dc to +7.0 V dc CC input voltage range (V ) ......................................................................... -0.5 V dc to V + 0.5 V dc IN CC Output and I/O voltage range (V ) ....................................................... -0.5 V dc to V + 0.5 V dc 2/ OUT CC DC input diode current (I ) ..................................................................... 20 mA IK DC output diode current (I ) .................................................................. 50 mA OK DC output current ................................................................................... 100 mA Maximum power dissipation (P ) ............................................................ 500 mW 3/ D Storage temperature range (T ) .......................................................... -65C to +150 C STG Lead temperature (soldering, 10 seconds) ............................................. +300C Thermal resistance, junction-to-case ( ) .............................................. See MIL-STD-1835 JC Junction temperature (T ) ....................................................................... +175C J 1.4 Recommended operating conditions. Supply voltage range (V ) ..................................................................... +4.5 V dc to +5.5 V dc CC Maximum low level input voltage (V )..................................................... 0.8 V dc IL Minimum high level input voltage (V ) .................................................... 2.0 V dc IH Output voltage range (V ) .................................................................... 0.0 V to V OUT CC Case operating temperature range (T ) .................................................. -55C to +125 C C 1/ All voltages are referenced to ground. 2/ For V 6.5 V dc, the upper bound is limited to V . CC CC 3/ Must withstand the added P due to short circuit test, I . D OS SIZE STANDARD 5962-89730 A MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS REVISION LEVEL SHEET COLUMBUS, OHIO 43218-3990 C 2 DSCC FORM 2234 APR 97