5962-8975401LA E2v

REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes IAW NOR 5962-R078-93. --tvn 93-01-29 Monica L. Poelking B Update to reflect latest changes in format and requirements. Editorial changes 04-08-11 Raymond Monnin throughout. --les THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Larry T. Gauder DEFENSE SUPPLY CENTER COLUMBUS CHECKED BY COLUMBUS, OHIO 43218-3990 STANDARD 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89754 01 L A Drawing number Device type Case outline Lead finish (see 1.2.1) (see 1.2.2) (see 1.2.3) 1.2.1 Device type. The device type identifies the circuit function as follows: Device type Generic number Circuit function 01 54F646 Transceivers/registers 02 54F648 Transceivers/registers,inverted 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style L GDIP3-T24 or CDIP4-T24 24 dual-in-line K GDFP2-F24 or CDFP3-F24 24 flat 3 CQCC1-N28 28 square chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage range ..................................................... -0.5 V dc to +7.0 V dc Input voltage range ....................................................... -0.5 V dc to +7.0 V dc Input current range ........................................................ -30 mA to +5.0 mA Voltage applied to any output in the disabled state ....... -0.5 V dc to +5.5 V dc Voltage applied to any output in the high state .............. -0.5 V dc to V CC Current into any output in the low state ......................... 96 mA Maximum power dissipation (P ) ................................... 825 mW 1/ D Storage temperature range ............................................ -65C to +150C Ambient temperature under bias ................................... -55C to +125C Lead temperature (soldering, 10 seconds) .................... +300C Junction temperature (T ) .............................................. +175C J Thermal resistance, junction-to-case ( ) ..................... See MIL-STD-1835 JC 1.4 Recommended operating conditions. Supply voltage range (V ) ...................................................... +4.5 V dc minimum to +5.5 V dc maximum CC Minimum high level input voltage (V ) ..................................... 2.0 V dc IH Maximum low level input voltage (V ) ...................................... 0.8 V dc IL Maximum input clamp current (I ) ........................................... -18 mA IC Maximum high level output current (I ) ................................... -12 mA OH Maximum low level output current (I ) .................................... +48 mA OL Case operating temperature range (T ) ................................... -55C to +125C C 1/ Maximum power dissipation is defined as V X I , and must withstand the added P due to short circuit CC CC D output test e.g., I . O SIZE STANDARD 5962-89754 A MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS REVISION LEVEL SHEET COLUMBUS, OHIO 43218-3990 B 2 DSCC FORM 2234 APR 97