5962-8986305UA E2v

REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED 06-11-08 Raymond Monnin A Boilerplate update, part of 5 year review. ksr THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV A A A A A A SHEET 15 16 17 18 19 20 REV STATUS REV A A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY James E. Jamison DEFENSE SUPPLY CENTER COLUMBUS CHECKED BY COLUMBUS, OHIO 43218-3990 STANDARD 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89863 01 X A Drawing number Device type Case outline Lead finish (see 1.2.1) (see 1.2.2) (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number 1/ Circuit function Acess time 01 512 X 9 FIFO 80 ns 02 512 X 9 FIFO 65 ns 03 512 X 9 FIFO 50 ns 04 512 X 9 FIFO 40 ns 05 512 X 9 FIFO 30 ns 06 512 X 9 FIFO 25 ns 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X GDIP1-T28 or CDIP2-T28 28 dual-in-line package Y CDIP3-T28 or GDIP4-T28 28 dual-in-line package Z CQCC1-N32 32 rectangular chip carrier package U GDFP2-F28 28 flat package 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage to ground potential ------------------------------ -0.5 V dc to +7.0 V dc DC voltage applied to outputs in high Z state ---------------- -0.5 V dc to +7.0 V dc DC input voltage ----------------------------------------------------- -0.3 V dc to +7.0 V dc DC output current ---------------------------------------------------- 20 mA Maximum power dissipation 2/ ----------------------------------- 1.0 W Lead temperature (soldering, 10 seconds) -------------------- +260 C Thermal resistance, junction-to-case ( ) -------------------- See MIL-STD-1835 JC Junction temperature (T ) 3/ ------------------------------------- +150 C J Storage temperature range --------------------------------------- -65 C to +150 C Temperature under bias ------------------------------------------- -55 C to +125 C 1.4 Recommended operating conditions. Supply voltage (V )------------------------------------------------- +4.5 V dc to +5.5 V dc CC Ground voltage (GND) ---------------------------------------------- 0 V dc Input high voltage (V ) -------------------------------------------- 2.2 V dc minimum IH Input low voltage (V ) ---------------------------------------------- 0.8 V dc maximum IL Case operating temperature range (T)------------------------ -55 C to +125 C C 1/ Generic numbers are listed on the Standardized Military Drawing Source Approval Bulletin at the end of this document and will also be listed in MIL-HDBK-103. 2/ Must withstand the added P due to short circuit test (e.g., I ). D OS 3/ Maximum junction temperature may be increased to +175 C during burn-in and steady-state life. SIZE STANDARD 5962-89863 A MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS REVISION LEVEL SHEET COLUMBUS, OHIO 43218-3990 A 2 DSCC FORM 2234 APR 97