INCH-POUND MIL-M-38510/101K 14 December 2005 SUPERSEDING MIL-M-38510/101J 07 February 2003 MILITARY SPECIFICATION MICROCIRCUITS, LINEAR, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON This specification is approved for use by all Departments and Agencies of the Department of Defense. Inactive for new design after 13 July 1995. The requirements for acquiring the product herein shall consist of this specification sheet and MIL-PRF-38535. 1. SCOPE 1.1 Scope. This specification covers the detail requirements for monolithic silicon, operational amplifiers. Two product assurance classes and a choice of case outlines and lead finish are provided for each type and are reflected in the complete part number. For this product, the requirements of MIL-M-38510 have been superseded by MIL-PRF-38535, (see 6.4). 1.1.2 Part or identifying number (PIN). The PIN is in accordance with MIL-PRF-38535, and as specified herein. 1.2.1 Device types. The device types are as follows: Device type Circuit 01 Single operational amplifier - internally compensated 02 Dual operational amplifier - internally compensated 03 Single operational amplifier - externally compensated 04 Single operational amplifier - externally compensated 05 Dual operational amplifier - externally compensated 1/ 06 Dual operational amplifier - externally compensated 1/ 07 Single operational amplifier, high speed 08 Dual operational amplifier - internally compensated 1.2.2 Device class. The device class is the product assurance level as defined in MIL-PRF-38535. 1/ Device types 05 and 06 may be monolithic, or they may consist of two separate, independent die. Comments, suggestions, or questions on this document should be addressed to: Commander, Defense Supply Center Columbus, ATTN: DSCC-VAS, 3990 East Broad St., Columbus, OH 43218-3990, or emailed to linear dscc.dla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at MIL-M-38510/101K 1.2.3 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style A 2/ GDFP5-F14 or CDFP6-F14 14 Flat pack B 2/ GDFP4-14 14 Flat pack C GDIP1-T14 or CDIP2-T14 14 Dual-in-line D GDFP1-F14 or CDFP2-F14 14 Flat pack E GDIP1-T16 or CDIP2-T16 16 Dual-in-line F GDFP2-F16 or CDFP3-F16 16 Flat pack G MACY1-X8 8 Can H GDFP1-F10 or CDFP2-F10 10 Flat pack I MACY1-X10 10 Can P GDIP1-T8 or CDIP2-T8 8 Dual-in-line Z GDFP1-G10 10 Flat pack with gullwing leads 2 CQCC1-N20 20 Square leadless chip carrier 1.3 Absolute maximum ratings. Supply voltage range (V ) ............................................................................ 22 V dc 3/ CC Input voltage range ......................................................................................... 20 V dc 4/ Differential input voltage range ....................................................................... 30 V dc 5/ Input current range ......................................................................................... -0.1 mA to +10 mA Storage temperature range ............................................................................ -65C to +150C Output short-circuit duration ........................................................................... Unlimited 6/ Lead temperature (soldering, 60 seconds) ..................................................... +300C Junction temperature (T ) ...............................................................................+175C 7/ J 1.4 Recommended operating conditions. Supply voltage (V ) ...................................................................................... 5 V dc to 20 V dc CC Ambient temperature range (T ) ....................................................................-55C to +125C A 2/ Inactive package case outline. 3/ Voltages in excess of these may be applied for short-term tests if voltage difference does not exceed 44 volts. 4/ For supply voltages less than 20 V dc, the absolute maximum input voltage is equal to the supply voltage. 5/ For device types 04, 06, and 07 only, this rating is 1.0 V unless resistances of 2 k or greater are inserted in series with the inputs to limit current in the input shunt diodes to the maximum allowable value. 6/ Short circuit may be to ground or either supply. Rating applies to +125C case temperature or +75C ambient temperature. 7/ For short term test (in the specific burn-in and life test configuration when required and up to 168 hours maximum) T = +275C. J 2