INCH-POUND MIL-M-38510/337B 23 January 2004 SUPERSEDING MIL-M-38510/337A 9 August 1983 MILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, BIPOLAR, ADVANCED SCHOTTKY TTL, DECODERS, MONOLITHIC SILICON Reactivated after 23 January 2004 and may be used for either new or existing design acquisition. This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product herein shall consist of this specification sheet and MIL-PRF 38535 1. SCOPE 1.1 Scope. This specification covers the detail requirements for monolithic silicon, advanced Schottky TTL, decoder microcircuits. Two product assurance classes and a choice of case outlines and lead finishes are provided for each type and are reflected in the complete part number. For this product, the requirements of MIL-M-38510 have been superseded by MIL-PRF-38535, (see 6.3). 1.2 Part or Identifying Number (PIN). The PIN is in accordance with MIL-PRF-38535, and as specified herein. 1.2.1 Device types. The device types are as follows: Device type Circuit 01 Decoder, 3 of 8, active low outputs with enable inputs 02 Dual decoder, 2 of 4, active low outputs with enable inputs 1.2.2 Device class. The device class is the product assurance level as defined in MIL-PRF-38535. 1.2.3 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line F GDFP2-F16 or CDFP3-F16 16 Flat pack X CQCC2-N20 20 Square leadless chip carrier 2 CQCC1-N20 20 Square leadless chip carrier Comments, suggestions, or questions on this document should be addressed to: Commander, Defense Supply Center Columbus, ATTN: DSCC-VAS, 3990 East Broad St., Columbus, OH 43216-5000, or emailed to bipolar dscc.dla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at www.dodssp.daps.mil. AMSC N/A FSC 5962 MIL-M-38510/337B 1.3 Absolute maximum ratings. Supply voltage range ............................................................................. -0.5 V dc to +7.0 V dc Input voltage range ................................................................................ -1.2 V dc at -18 mA to +7.0 V dc Storage temperature range .................................................................... -65 to +150C Maximum power dissipation, per device (P ) 1/ D Device type 01 ................................................................................. 110 mW Device type 02 ................................................................................. 110 mW Lead temperature (soldering, 10 seconds) ............................................. +300C Thermal resistance, junction to case ( ): JC Cases E, F, X, and 2 ............................................................................ (See MIL-STD-1835) Junction temperature (T ) 2/ ................................................................... 175C J 1.4 Recommended operating conditions. Supply voltage (V ) .............................................................................. 4.5 V minimum to 5.5 V maximum CC Minimum high level input voltage (V ) ................................................... 2.0 V dc IH Maximum low level input voltage (V ) .................................................... 0.8 V dc IL Case operating temperature range (T ) ................................................. -55 to +125C C 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications and Standards. The following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38535 - Integrated Circuits (Microcircuits) Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard for Microelectronics. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines (Copies of these documents are available online at