Embedded Artists iMX7 Dual COM Board rev A The Art of Embedded Systems Development made Easy Document status: Preliminary iMX7 Dual COM Board Feature Highlights NXP i.MX 7Dual, dual-core ARM Cortex-A7 and Cortex-M4, 1GHz/200MHz High performance 2x1800+250 DMIPS 1 GByte DDR3L 1066 MT/s, 32-bit databus 4 GByte eMMC on-board Flash 24-bit parallel RGB and MIPI-DSI graphical output PCIe, USB, CAN and many more interfaces Low-power consumption - very power efficient Linux and Android BSP 82 x 50 mm small form factor Long term availability Introduction The iMX7 Dual COM Board provides a quick and easy solution for implementing a high-performance ARM dual-core Cortex-A7 / Cortex- M4 based design. The Cortex-A7 / Cortex-M4 heterogeneous architecture enables the system to run an OS like Linux on the dual-core Cortex-A7 and a Real-Time OS (RTOS) on the Cortex-M4. The i.MX 7Dual supports 2D graphical acceleration and has dual display outputs (RGB and MIPI-DSI). The design has a low-power implementation with DDR3L memories and a PMIC supporting DVFS techniques. Typical applications are graphical interface solutions, communication solutions and connected real-time systems. Specification Processor Cores NXP i.MX 7Dual dual-core ARM Cortex-A7 and Cortex-M4 Frequency 1 GHz on Cortex-A7 200 MHz on Cortex-M4 Memory SDRAM 1 GByte DDR3L 1066 MT/s, 32-bit databus NAND FLASH 4 GByte eMMC NAND Flash for OS and bootloader QSPI FLASH 32 MByte QSPI NOR Flash for Cortex-M4 code Graphics Parallel RGB 24-bit, up to 1920 x 1080 pixels at 60 Hz output MIPI-DSI 2 lanes, maximum bit rate of 1.5 Gbps LVDS Optional via MIPI-DSI-to-LVDS brige Graphics Engine PXP - PiXel processing pipeline for imagine resize, rotation, overlay and color space conversion. Graphics CMOS sensor interface Parallel, up to 24 bit input (camera) Serial, MIPI-CSI2, 2 lanes, maximum bit rate of 1.5 Gbps Ethernet One 10/100/1000 Mbps Gigabit Ethernet interface based on Atheros AR8031 Ethernet PHY Second Gigabit Ethernet interface requires off-board Ethernet-PHY I/O PCIe 1x PCIe 2.1, 1x lane (all functions USB 2x USB2.0 OTG, 1x HSIC are not UART, SPI, I2C, Audio 7x UART, 4x SPI, 4x I2C, 3x I2S/SSI available at CAN 2x CAN bus 2.0B the same GPIO Large number of GPIOs and keypad pins available time) Memory card 2x SD3.0/MMC5.0 ADC 8ch 12-bit resolution Other Boot parameters E2PROM storing board information including Ethernet MAC address and memory bus setup params. Watchdog On-board watchdog functionality RTC i.MX 7Dual on-chip RTC Power Management (PMIC) PMIC (MMPF3000) supporting DVFS techniques for low power modes Embedded Artists AB Phone/Fax: +46 (0)40-611 00 93 Copyright 2020 Embedded Artists AB. All rights reserved. All other products or service names mentioned herein are Jrgen Ankersgatan 12 Embedded Artists iMX7 Dual COM Board rev A The Art of Embedded Systems Development made Easy Document status: Preliminary Power Supply voltage +3.3V Power consumption TBD Environment Operating Temperature 0 - 70 and -20 - 85 Celsius Operating Humidity 5 - 90% relative humidity, non-condensing Mechanical Dimensions (W x H x D) 82 x 50 mm, same as SMARC form factor but different pinning for better carrier board routing Connectors 314 pos MXM3 edge connector, 0.5 mm pitch 10 pos 0.5 mm pitch FPC for JTAG Block Diagram DDR3L Memory JTAG (32 bit data bus) connector NXP i.MX 7Dual with dual-core ARM Parameter SD3 eMMC Flash storage Cortex-A7 / Cortex-M4 1 GHz / 200 MHz QSPIA QSPI Flash I2C 0 PMIC 10/100/1000 Mbps Boot 3.3V input Ethernet-PHY control MXM3 connector (314 pins) Ordering Information 1 Part No. CPU SDRAM eMMC QSPI MIPI-DSI Supply Operating to LVDS Voltage Temperature EAC00274 MCIMX7D7DVM10S 1 GByte DDR3L 4 GByte 32 Mbyte No 3.3V 0 - 70 C EAC00276 MCIMX7D5EVM10S 1 GByte DDR3L 4 GByte 32 Mbyte No 3.3V -20 - 85 C 1 Standard configurations listed. Others on request. Support Highlights Development Kit Embedded Artists is a reliable and competent partner The iMX7 Dual COM Board is supported by the iMX7 Dual - we help you become successful Developer s Kit V2 that provides a quick path to get started with development and integration work. Professional and responsive support The kit provides reference implementations of key interfaces. Pre-designed standard Carrier boards for integration Ordering part No. EAK00329 Custom Carrier board design Customization o Different pinning, supply voltage, memory sizes, etc o Single Board Computer (SBC) solutions Display solutions Mechanical solutions Schematic review of customer carrier board designs Driver and application development Disclaimer: Embedded Artists reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. Embedded Artists AB Phone/Fax: +46 (0)40-611 00 93 Copyright 2020 Embedded Artists AB. All rights reserved. All other products or service names mentioned herein are Jrgen Ankersgatan 12