Embedded Artists iMX6 SoloX COM Board rev A The Art of Embedded Systems Development made Easy Document status: Preliminary iMX6 SoloX COM Board Feature Highlights NXP ARM Cortex-A9 and Cortex-M4 i.MX 6SoloX running at 1 GHz / 227 MHz 1 GByte DDR3L 800 MT/s, 32-bit databus 4 GByte eMMC on-board Flash 16 MByte QSPI 24-bit parallel RGB and LVDS graphical output OpenGL ES 2.0 for 3D, BitBlt for 2D and OpenVG 1.1 Dual 10/100/1000 Gigabit Ethernet with on-board PHY Low-power consumption Linux BSP 82 x 50 mm small form factor Long term availability Introduction The iMX6 SoloX COM Board provides a quick and easy solution for implementing a high-performance ARM Cortex-A9/M4 based design. The heterogeneous multiprocessing architecture enables the system to run an OS like Linux on the Cortex-A9 and a Real-Time OS (RTOS) on the Cortex-M4. The i.MX 6SoloX supports 2D/3D graphical acceleration and has two display outputs (RGB and LVDS). The design has a low-power implementation with DDR3L memories and a PMIC supporting DVFS techniques, making the board ideal for portable applications. Other typical applications are graphical interface solutions, communication solutions and connected real-time systems. Specification Processor Cores NXP ARM Cortex-A9 and Cortex-M4 i.MX6SoloX Frequency 1 GHz on Cortex-A9 227 MHz on Cortex-M4 Memory SDRAM 1 GByte DDR3L 800 MT/s, 32-bit databus NAND FLASH 4 GByte eMMC NAND Flash for OS and bootloader QSPI FLASH 16 MByte dual QSPI NOR Flash for Cortex-M4 code Graphics LVDS 18/24 bit, up to 85 Mpixels/sec, for example WXGA (1366 x 768 px) at 60 Hz output Parallel RGB 24-bit, up to WXGA (1366 x 768 px) at 60 Hz Graphics Engine GPU (GC400T) supporting OpenGL ES 1.1/2.0 and OpenVG 1.1 APIs Graphics Digital CMOS sensor interface (camera), parallel interface input Analogue NTSC/PAL analogue video input interface (4 ch) Ethernet Dual 10/100/1000 Mbps Gigabit Ethernet interface based on Atheros AR8031 Ethernet PHY I/O PCIe 1x PCIe 2.0, 1x Lane (all functions USB 1x USB2.0 OTG, 1x USB2.0 Host are not UART, SPI, I2C, Audio 6x UART, 5x SPI, 4x I2C, ESAI, 3x I2S/SSI, S/PDIF TX/RX available at CAN 2x CAN bus 2.0B the same GPIO Up to 99 pins and 8 pins for keypad time) Memory card 3x SD/MMC 4.5 ADC 2x 4ch 12-bit resolution Other Boot parameters E2PROM storing board information including Ethernet MAC address and memory bus setup params. RTC i.MX6SoloX on-chip RTC Watchdog On-board watchdog functionality Power Management (PMIC) PMIC (MMPF0200) supporting DVFS techniques for low power modes Power Supply voltage +3.3V Power consumption See datasheet for details, but 1-2 Watt typical when active Embedded Artists AB Phone: +46 (0)40-611 00 93 Copyright 2020 Embedded Artists AB. All rights reserved. All other products or service names mentioned herein are Jrgen Ankersgatan 12 Embedded Artists iMX6 SoloX COM Board rev A The Art of Embedded Systems Development made Easy Document status: Preliminary Environment Operating Temperature 0 - 70 Celsius or -40 - 85 Celsius Operating Humidity 5 - 90% relative humidity, non-condensing Mechanical Dimensions (W x D) 82 x 50 mm, same as SMARC form factor but different pinning for better carrier board routing Connectors 314 pos MXM3 edge connector, 0.5 mm pitch 10 pos 0.5 mm pitch FPC for JTAG Block Diagram DDR3L Memory JTAG (32 bit data bus) connector NXP i.MX 6SoloX with ARM Parameter SD3 eMMC Flash storage Cortex-A9 / Cortex-M4 1 GHz / 227 MHz QSPI2 Dual QSPI Flash I2C 0 PMIC Dual 10/100/1000 Mbps Boot 3.3V input Ethernet-PHY control MXM3 connector (314 pins) Ordering Information 1 Part No. CPU SDRAM eMMC QSPI Ethernet Pinning Supply Operating Voltage Temperature EAC00244 MCIMX6X4EVM10AB 1 GByte 4 GByte Dual, Dual EACOM 3.3V 0 - 70 C DDR3L 16 Mbyte 1 Gbps board spec EAC00256 MCIMX6X4CVM08AB 1 GByte 4 GByte Dual, Dual EACOM 3.3V -40 - 85 C DDR3L 16 Mbyte 1 Gbps board spec 1 Standard configurations listed. Others on request. Support Highlights Development Kit Embedded Artists is a reliable and competent partner The iMX6 SoloX COM Board is supported by the - we help you become successful iMX6 SoloX Developer s Kit V2 that provides a quick path to get started with development and integration work. Professional and responsive support The kit provides reference implementations of key Pre-designed standard Carrier boards for interfaces. integration Ordering part No. EAK00331 Custom Carrier board design Customization o Different pinning, supply voltage, memory sizes, etc o Single Board Computer (SBC) solutions Display solutions Mechanical solutions Schematic review of customer carrier board designs Driver and application development Disclaimer: Embedded Artists reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. Embedded Artists AB Phone: +46 (0)40-611 00 93 Copyright 2020 Embedded Artists AB. All rights reserved. All other products or service names mentioned herein are Jrgen Ankersgatan 12