Embedded Artists iMX6 DualLite COM Board rev A The Art of Embedded Systems Development made Easy Document status: Preliminary iMX6 DualLite COM Board Feature Highlights NXP dual-core ARM Cortex-A9 i.MX 6DualLite 1GHz 1 GByte DDR3L 800 MT/s, 64-bit databus 4 GByte eMMC on-board Flash 24-bit parallel RGB, dual LVDS, HDMI, MIPI-DSI graphical output OpenGL ES 2.0 for 3D, BitBlt for 2D and OpenVG 1.1 10/100/1000 Gigabit Ethernet with on-board PHY PCIe, SATA, USB, CAN and many more interfaces Low-power consumption Linux BSP 82 x 50 mm small form factor Long term availability Introduction The iMX6 DualLite COM Board provides a quick and easy solution for implementing a high-performance ARM dual-core Cortex-A9 based design. The system is ideal for running an OS like Linux. The i.MX 6DualLite supports 2D/3D graphical acceleration and has multiple display outputs (RGB, LVDS, HDMI and MIPI-DSI). The design has a low-power implementation with DDR3L memories and a PMIC supporting DVFS techniques, making the board ideal for portable applications. Other typical applications are graphical interface solutions, communication solutions and connected real-time systems. Specification Processor Cores NXP dual-core ARM Cortex-A9 i.MX 6DualLite Frequency 1 GHz on Cortex-A9 Memory SDRAM 1 GByte DDR3L 800 MT/s, 64-bit databus NAND FLASH 4 GByte eMMC NAND Flash for OS and bootloader Graphics LVDS Dual 18/24 bit, up to 85 Mpixels/sec, for example WXGA (1366 x 768 px) at 60 Hz output Parallel RGB 24-bit, up to WXGA (1366 x 768 px) at 60 Hz HDMI V1.4, up to 1920 x 1080 px MIPI-DSI 2 lanes Graphics Engines GPU (GC2000/GC355/GC320) supporting OpenGL ES 3.0 and OpenVG 1.1 APIs Hardware video decoder: 1080p60h H.264 HP Hardware video encoder: 1080p30h H.264 BP / Dual 720p Graphics CMOS sensor interface Parallel, up to 20 bit input (camera) Serial, MIPI-CSI2, 4 lanes Ethernet 10/100/1000 Mbps Gigabit Ethernet interface based on Atheros AR8031 Ethernet PHY I/O PCIe 1x PCIe 2.0, 1x lane (all functions USB 1x USB2.0 OTG, 1x USB2.0 Host are not UART, SPI, I2C, Audio 5x UART, 5x SPI, 3x I2C, ESAI, 3x I2S/SSI, S/PDIF TX/RX available at CAN 2x CAN bus 2.0B the same GPIO Up to 99 pins and 8 pins for keypad time) Memory card 3x SD/MMC 4.5 SATA 1x SATA-II Other Boot parameters E2PROM storing board information including Ethernet MAC address and memory bus setup params. RTC i.MX 6Quad on-chip RTC Watchdog On-board watchdog functionality Power Management (PMIC) PMIC (MMPF0100) supporting DVFS techniques for low power modes Embedded Artists AB Phone/Fax: +46 (0)40-611 00 93 Copyright 2020 Embedded Artists AB. All rights reserved. All other products or service names mentioned herein are Jrgen Ankersgatan 12 Embedded Artists iMX6 DualLite COM Board rev A The Art of Embedded Systems Development made Easy Document status: Preliminary Power Supply voltage +3.3V Power consumption TBD Environment Operating Temperature 0 - 70 or -40 - 85 Celsius Operating Humidity 5 - 90% relative humidity, non-condensing Mechanical Dimensions (W x D) 82 x 50 mm, same as SMARC form factor but different pinning for better carrier board routing Connectors 314 pos MXM3 edge connector, 0.5 mm pitch 10 pos 0.5 mm pitch FPC for JTAG Block Diagram DDR3L Memory JTAG (64 bit data bus) connector NXP i.MX 6DualLite Parameter SD4 with dual-core ARM eMMC Flash storage Cortex-A9 1 GHz I2C 0 PMIC 10/100/1000 Mbps Boot 3.3V input Ethernet-PHY control MXM3 connector (314 pins) Ordering Information 1 Part No. CPU SDRAM eMMC Ethernet Pinning Supply Operating Voltage Temperature EAC00261 MCIMX6U5DVM10AC 1 GByte DDR3L 4 GByte 1 Gbps EACOM board 3.3V 0 - 70 C spec EAC00262 MCIMX6U7CVM08AC 1 GByte DDR3L 4 GByte 1 Gbps EACOM board 3.3V -40 - 85 C spec 1 Standard configurations listed. Others on request. Support Highlights Development Kit Embedded Artists is a reliable and competent partner The iMX6 DualLite COM Board is supported by the iMX6 - we help you become successful DualLite Developer s Kit V2 that provides a quick path to get Professional and responsive support started with development and integration work. The kit provides reference implementations of key interfaces. Pre-designed standard Carrier boards for integration Ordering part No. EAK00342 Custom Carrier board design Customization o Different pinning, supply voltage, memory sizes, etc o Single Board Computer (SBC) solutions Display solutions Mechanical solutions Schematic review of customer carrier board designs Driver and application development Disclaimer: Embedded Artists reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. Embedded Artists AB Phone/Fax: +46 (0)40-611 00 93 Copyright 2020 Embedded Artists AB. All rights reserved. All other products or service names mentioned herein are Jrgen Ankersgatan 12