Embedded Artists iMX7 Dual uCOM Board rev A The Art of Embedded Systems Development made Easy Document status: Preliminary iMX7 Dual uCOM Board Feature Highlights NXP i.MX 7Dual, dual-core ARM Cortex-A7 and Cortex-M4, 1GHz/200MHz High performance 2x1800+250 DMIPS 1 GByte LPDDR3 1066 MT/s, 32-bit databus 8 GByte eMMC on-board Flash 24-bit parallel RGB and MIPI-DSI graphical output PCIe, USB, CAN and many more interfaces 27 mm actual size ROHM PMIC BD71815GW with on-chip battery charger Low-power consumption - very power efficient Linux and Android BSP 27 x 37 mm ultra small form factor Long term availability Introduction The iMX7 Dual uCOM Board provides a quick and easy solution for implementing a high-performance ARM dual-core Cortex-A7 / Cortex-M4 based design. The Cortex-A7 / Cortex-M4 heterogeneous architecture enables the system to run an OS like Linux on the dual-core Cortex-A7 and a Real-Time OS (RTOS) on the Cortex-M4. The i.MX 7Dual supports 2D graphical acceleration and has dual display outputs (RGB and MIPI-DSI). The design has a low-power implementation with LPDDR3 memories and a PMIC supporting DVFS techniques and integrated battery charger, making the board ideal for portable applications. Other typical applications are graphical interface solutions, communication solutions and connected real-time systems. Specification Processor Cores NXP i.MX 7Dual dual-core ARM Cortex-A7 and Cortex-M4 Frequency 1 GHz on Cortex-A7 200 MHz on Cortex-M4 Memory SDRAM 1 GByte LPDDR3 1066 MT/s, 32-bit databus NAND FLASH 8 GByte eMMC NAND Flash for OS and bootloader Graphics Parallel RGB 24-bit, up to 1920 x 1080 pixels at 60 Hz output MIPI-DSI 2 lanes, maximum bit rate of 1.5 Gbps Graphics Engine PXP - PiXel processing pipeline for imagine resize, rotation, overlay and color space conversion. Graphics CMOS sensor interface Parallel, up to 24 bit input (camera) Serial, MIPI-CSI2, 2 lanes, maximum bit rate of 1.5 Gbps Ethernet Two 10/100/1000 Mbps Gigabit Ethernet interfaces (requires off-board Ethernet-PHY) I/O PCIe 1x PCIe 2.1, 1x lane (all functions USB 2x USB2.0 OTG, 1x HSIC are not UART, SPI, I2C, Audio 7x UART, 4x SPI, 4x I2C, 3x I2S/SSI available at CAN 2x CAN bus 2.0B the same GPIO Large number of GPIOs and keypad pins available time) Memory card 2x SD3.0/MMC5.0 ADC 4ch 12-bit resolution Other Boot parameters E2PROM storing board information including Ethernet MAC address and memory bus setup params. Watchdog On-board watchdog functionality RTC ROHM BD71815GW integrated low-power RTC Power Management (PMIC) ROHM BD71815GW supporting DVFS techniques for low power modes Battery Charger ROHM BD71815GW with Coulomb counter for battery fuel gauging. Up to 28V input voltage White LED Driver 25mA, up to 26V Embedded Artists AB Phone/Fax: +46 (0)40-611 00 93 Copyright 2020 Embedded Artists AB. All rights reserved. All other products or service names mentioned herein are Jrgen Ankersgatan 12 Embedded Artists iMX7 Dual uCOM Board rev A The Art of Embedded Systems Development made Easy Document status: Preliminary Power Supply voltage +3.3V Power consumption TBD Environment Operating Temperature 0 - 70 or -20 - 85 Celsius Operating Humidity 5 - 90% relative humidity, non-condensing Mechanical Dimensions (W x H x D) 27 x 37 x 4 mm Connectors 70 pos DF40C-70DP-0.4V connector with 0.4mm pitch Dual 100 pos DF40C-100DP-0.4V connector with 0.4mm pitch Block Diagram LPDDR3 Memory NXP i.MX 7Dual (32 bit data bus) with dual-core ARM Parameter Cortex-A7 / Cortex-M4 storage SD3 eMMC Flash 1 GHz / 200 MHz I2C 0 PMIC Boot 3.3V input control 70 pos + 2x 100 pos DF40C connector (270 pins in total) Ordering Information 1 Part No. CPU SDRAM eMMC I/O Supply Operating 2 Voltage Voltage Temperature EAC00266 MCIMX7D7DVK10SC 1 GByte LPDDR3 8 GByte 3.3V 3.3V 0 - 70 C EAC00267 MCIMX7D5EVK10SC 1 GByte LPDDR3 8 GByte 3.3V 3.3V -20 - 85 C Note, no EPDC peripheral 1 Standard configurations listed. Others on request. 2 1.8V I/O voltage on request. Support Highlights Development Kit Embedded Artists is a reliable and competent partner The iMX7 Dual uCOM Board is supported by the iMX7 Dual - we help you become successful uCOM Developer s Kit V2 that provides a quick path to get Professional and responsive support started with development and integration work. The kit provides reference implementations of key interfaces. Pre-designed standard Carrier boards for integration Ordering part No. EAK00344 Custom Carrier board design Customization o Different pinning, supply voltage, memory sizes, etc o Single Board Computer (SBC) solutions Display solutions Mechanical solutions Schematic review of customer carrier board designs Driver and application development Disclaimer: Embedded Artists reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. Embedded Artists AB Phone/Fax: +46 (0)40-611 00 93 Copyright 2020 Embedded Artists AB. All rights reserved. All other products or service names mentioned herein are Jrgen Ankersgatan 12