Portable high-speed USB In-System (ISP) Programmer Portable ISP Programmer for Field-Service and Production applications The EPSILON5 MK IV programmer being used in standalone mode The EPSILON5 MK IV is a high-speed portable ISP programmer designed for field and low-volume production programming applications. The programmer supports programming of many in-system programmable (ISP) FIELD-SERVICE microcontrollers including AVR, 8051, ARM and Zensys Z-wave devices. It can be operated under PC control during development and for project configuration PRODUCTION PROGRAMMING / uploading using the EQTools Toolsuite. For field / production applications the unit is designed to operate in Standalone Mode. A Standalone TARGET / USB POWERED Programming Project can be recalled from the on-board non-volatile FLASH memory and programmed into a Target System by pressing a single key. All the FIRMWARE UPGRADEABLE popular ISP connection headers are catered for. Portable In-System (ISP) Programmer Ideal for Field-service or low-volume Production programming Supports In-system Programming (ISP) of many different programmable microcontrollers and serial memory devices Supports programming via SPI, JTAG, I2C and UART interfaces Supports Standalone operation - no PC required after programmer has been configured Low power consumption allows the programmer to be powered from most Target Systems (no external supply required) High-speed USB connection to PC Backwards compatible with Epsilon5 MKII / MKIII programmers Programmer can supply +5V regulated Programming Interfaces: power to the Target system when it is Supports most ISP hardware powered from an external supply interfaces / protocols including JTAG, SPI, Power supply is reverse-polarity protected I2C, ATtiny AVR HV mode, 8051 UART Bootloader Fixed +12V Target VPP voltage generator for ATtiny HV devices Very fast programming speeds suitable for high-throughput production environments Robust I/O driver stage with ESD protection J3 Atmel J6 Equinox Individually configurable programmer I/O 6-way Header 10-way Header Pin 1 pins User-configurable RESET pin state and timing to cater for complicated RESET Pin 1 circuits / RESET monitoring ICs Pin 1 Pin 1 Supports programming of target ICs between 3.1 and 5.0V. Target J8 JTAG J7 Atmel Programmable frequency generator output Programmer Microcontroller 10-way Header 10-way Header ISP Connectors on SCK2 pin - supports external clocking of AVR microcontrollers to speed up User Target programming System ISP Cable Control methods: ISP connectors / headers: Atmel Header Equinox Header PC control in Development Mode (EDS) Most popular ISP connectors are catered for (6-way) (10-way) via high-speed USB port ARM standard 20-pin and 10-pin JTAG JTAG Header Atmel Header (10-way) (10-way) connectors requires a special ARM JTAG Standalone keypad / display operation cable (available separately) Standalone Mode: Software (as standard): Supports loading of 1 x Standalone EQTools - creates Standalone Programming Projects into the Programming Projects programmer memory (512 kbytes capacity) EDS - Development Mode for testing under Single-button auto-program operation PC control allows repetitive execution of the selected Programmer project (permanently stored in programmer) Upload Wizard - uploads projects to the PASS / BUSY / FAIL LEDs indicate programmer programmer status USB Cable Typical applications: Power Field-service programming Supply Unit (PSU) Low to medium volume standalone production programming Device support: PC Atmel AVR (not XMEGA or ATtiny TPI) ARM FLASH microcontrollers - Typical programmer connection to PC and ARM7TDMI , Cortex M3, Cortex M4 Target System (DUT) Selected 8051 FLASH microcontrollers Serial EEPROMs (I2C) Zensys Z-wave devices Power supply: The programmer can be powered from: - User Target System (3.1 - 5.0V 60mA) - External power supply via jack socket USB port External DC (6.0 - 12.0V 60mA) System Contents: (J5) Power Supply - PC USB Port (PC dependent) Input (CON1) The picture shows the typical contents of the - External USB Power Pack (+5V only) Epsilon5 MK IV programming kit. An external Bottom panel connections power supply is NOT included with the kit. Ordering information: EPSILON5MK4(STD) - Portable high-speed USB In-System (ISP) Programmer (standard device support version) EPSILON5MK4(AVR-JTAG) - Portable ISP Programmer - Atmel AVR - JTAG algorithms only EPSILON5MK4(ARM) - Portable ISP Programmer - for Atmel ARM Microcontrollers EPSILON5MK4(E2) - Portable ISP Programmer for Serial (I2C) EEPROM memory devices PSU-9V1700mA(UN) - External 9V DC 1.7A power supply for use with programmer Equinox Technologies reserves the right to change any information contained within this leaflet without prior notice. E&OE Equinox House, 217 Church Street Westhoughton, Bolton, Lancashire BL5 3SW United Kingdom Telephone: +44 (0)1942 841975 : Fax: +44 (0)1942 844181 : Email: info equinox-tech.com : Web: www.equinox-tech.com SCK2 0V Target Vcc