TROPO 15W Dimmable LED Driver Features TROPO switch mode power supply technology is designed to generate one constant current output from an AC input, and work with industry standard lighting controls in dimming applications. 120VAC and 230VAC Inputs Available Output current availability 0.35A-1.5A. Consult Factory for customized programming Operates with Industry Standard Dimmers Compact Encapsulated Assembly Active Power Factor Correction Output Over-Voltage, Over-Current and Short-Circuit Protection and Auto Recovery High Temperature Operation (up to 90C case) UL Approved, ENEC Approved, CE Mark 60-120 W EVM Series Long Life ROHS Compliant Tri-Mode Dimming (0-10 V & TRIAC/ELV) TROPO is designed for powering LED luminaries with standard lighting controls. The modules operate with: Standard Light Switches Constant Current LED Drivers with Deep Dimming Triac based Incandescent Dimmers (Standard phase leading edge) Electronic Low Voltage Dimmers (Reverse Phase trailing edge) Max.& Input& Output& Output& Max.&Case& Power& Dimming& Startup& Output& Efficiency &THD Dimming&Method TROPO is ideal for installations requiring dimmable Class 2 outputs such as: Voltage Voltage Current Temperature Factor Range Time Power 90 to 305 90C ForwardIPhase, Commercial Lighting Residential Lighting 1.05 to 2.8 A 87% 1 I 100% Vac 120 W 30 to 84 Vdc (measured at < 20% > 0.9 ReverseIPhase 400 ms CC typical (% of Iout) maximum the hot spot) & 0 I 10V CC: Constant Current The following diagram depicts a typical installation utilizing the TROPO: TRIAC Dimmer + Dim Dimmer - Dim Dimming range down to less then FEATURES Triac 10% nominal output current + LEDs Based 0-10 V Output current does not terminate CompaHble with TRIAC (forward-phase or leading-edge) / Dimmer Dimmer during off time of dimmer ELV (reverse-phase or trailing-edge) and 0-10 V dimmers Output Current factory settable up to 1.5A TRIAC dimming only at 120 Vac EVM110 TROPO Multiple Drivers / LED Assemblies Outdoor surge protecHon: 3 kV line to line/6 kV line to earth may be connected to a single Linear 0-10V dimming transfer funcHon: 10V=100%, 1V=10%, dimmer 0.1V=1% Facilitates compliance with Energy - LEDs ProtecHons: output open load, over-current and short-circuit Star ratings for LED luminares (hiccup), and over-temperature with auto recovery APPLICATION DIAGRAM Conducted and radiated EMI: Compliant with FCC CFR Title 47 Part 15 Class B (120 Vac)/Class A (277 Vac) and EN55015 (CISPR 15) at 220/230/240 Vac Enables ENERGY STAR and DLC (DesignLight ConsorHum) luminaire compliance IP20-rated Bo om Leads with Studs metal case with silicone-based poang. OpHonal IP64 metal case with side leads LifeHme: 50,000 hours 90C maximum case hot spot temperature Class 2 power supply (only some models) Double-insulated power supply between input and output (class II) Worldwide safety approvals METAL CASE L 144 x W 70 x H 40 mm (L 5.67 x W 2.76 x H 1.57 in) APPLICATIONS High Bay Lights Industrial LED LighHng Metal Halide replacement Tunnels and street lighHng Purple: + Dim Outdoor LED LighHng Wide-area downlights Suitable for driving high current COB LEDs such as Crees White: Neutral Grey: - Dim LED CXA3050/3070/3590, Bridgelux Vero series and modules such Red: + LEDs DRIVER as Crees LMH020 6000/8000 Black: Line Black: - LEDs WIRING DIAGRAM EVM Series Data Sheet 1 ERP - ENERGY RECOVERY PRODUCTS December 7, 2014 rev. A 60-120 W EVM Series Tri-Mode Dimming (0-10 V & TRIAC/ELV) Constant Current LED Drivers with Deep Dimming 1 - INPUT SPECIFICATION ( 25C ambient temperature) Units Minimum Typical Maximum Notes AC5Line5Input5Voltage5Range5 120/220/230/ Vac 90 305 (Vin) 240/277 Input5Frequency5Range Hz 47 600/050 63 Power5Factor5(PF) 0.9 >00.9 At0nominal0input0voltage Inrush5Current A Meets0NEMAL4100requirements At0any0point0on0the0sine0wave0and025C 2500A0 012000Vac Leakage5Current A 5000A0 02300Vac Measured0per0IEC60950L1 6000A0 02770Vac Input5Harmonics Complies0with0IEC61000L3L20for0Class0C0equipment At00nominal0input0voltage0and0nominal0LED0load Total5Harmonics5Distortion5 20% Complies0with0DLC0(DesignLight0Consortium)0 (THD) 000technical0requirements0v2.1 87% At01200Vac Efficiency L 89% At02770Vac Isolation Meets0UL60950L10for0class0II0reinforced/double0insulation0power0supply 2 - OUTPUT SPECIFICATION ( 25C ambient temperature) Units Minimum Typical Maximum Notes Output4Voltage4(Vout) Vdc 30 84.0 See+ordering+information+for+details Output4Current4(Iout) A 1.05 2.8 See+ordering+information+for+details Output4Current4Regulation % <5 2.5 +5 Includes+AC+line+voltage,+load,+and+current+set+point+variations The driver does not operate outside of the regulation requirements for more Output4Current4Overshoot % < < 10 than+500+ms+during+power+on+with+nominal+LED+load+and+without+dimmer. <+25%+peak<to<peak+of+rated+output+ Measured+at+nominal+LED+voltage+and+nominal+input+voltage+without+dimming. Ripple4Current current Calculated+in+accordance+with+the+IES+Lighting+Handbook,+9th+edition. Dimming4Range4(%4of4Iout) % 1 100 The+dimming+range+will+be+dependent+on+each+specific+dimmer. 400 With+nominal+LED+voltage+and+without+dimmer+attached StartDup4Time ms With nominalLED voltage,with anapproved dimmerattached (seelist ofapproved 500 dimmers+in+page+5)+and+at+the+full+dimming+conduction+angle Output4Controls A dimming input can be used to adjust the output settingvia astandard commercialwall dimmer,an externalcontrol +Dim,4DDim voltage source (0 to 10 Vdc), or a variable resistor whenusing the recommended numberof LEDs.The dimminginput permits+1%+to+100%+dimming. SaveEnergy ERPpowerllc.com 2 www.ERPpowerllc.com