STR-1 F&F

u l. K o n s ta n ty n o w s k a 7 9 /8 1 FUNCTIONING 9 5 -2 0 0 P a b ia n ic e te l/ fa x 4 8 4 2 2 2 7 0 9 7 1 P O L A N D Supplied the relay is to sigal by shine of green LED U. The roller e -m a il : fi f fi f. c o m .p l blind motor is activated by the momentary switching of a current pulse (L or N) to one of the control inputs. The motor is activated at a time programmed previously by the user . The activation time S S T T R R - - 1 1 programmed enables the complete lifting or lowering of the roller R O L L E R B L I N D C O N T R O L L E R blind. Also, there is a possibility of stopping the rolled blind activated at a level selected by the user (non-complete opening d o u b l e - b u t t o n t y p e or closing of the roller blind). Control inputs of relay: Local control - a group of push-buttons that controls one roller 5 9 0 8 3 1 2 5 9 3 3 0 0 > blind which are connect to joint 5 and 6. w w w . f i f . c o m . p l -upwards (opening) - downwards (closing). Pressing the local control push-button activates the movement of F& F p rod uc ts are co ve red by an 24 m on ths w arr an ty fro m da te of pu rch as e the roller blind in a selected direction. If the roller blind is already moving, pressing the local control push-button will stop the roller PURPOSE blind. The roller blind controller STR-1 is designed for controlling roller blinds (up and down movement) or other devices (for example, Central control - a common group of push-buttons which are gates) that are driven by a single-phase AC electric motor and connect to joint 7 and 8 for many controllers (minimum two controllers) that controls all roller blinds included in the central operated by means of momentary switches (for example, bell- pushes). The controller can operate as an independent unit control system (designated for opening/closing one roller blind) as well as the - all upwards - all downwards. Pressing the central control push-button activates the movement controllers can be combin ed in to groups that enable the central of the roller blinds in a selected direction. If one of the roller blinds controlling of many roller blinds is already moving in the same direction, its movement will be continued. If one of the roller blinds is moving in the opposite S T R S T R direction, this roller blind will be first stopped and then its movement will be activated in the direction in accordance with the command sent to the central input. L O C A L L O C A L C O N T R O L C O N T R O L A TTENTION The central control enables only activating the movement of the roller blinds in a selected direction. The roller blind will be stopped after the programmed movement time or C E N T R A L when any of the local control push-buttons is pressed. C O N T R O L WIRING DIAGRAM L L A O R R 1 2 3 4 5 6 7 8 T T r N N e E O l l C C o r t n o ) c N M d : l n i a l n b g i r s e l l l 8 o o r r t 7 o n L N L/N L/N L/N L/N o 6 w t c ( 5 h l t i o 4 r w t 3 n Description of connection: n M o 2 o i c t l 1 a 1 - 2 supply 230V (L - N) l a l r t a t n 3 supply of motor - output in to direction UPW ARDS s e n c i 4 supply of motor - output in to direction DOWNW ARDS r n o o f 5 local control - to direction UPW ARDS m m m a 6 local control - to direction DOWNW ARDS r o g c 7 local control - to direction UPW ARDS a i n 8 i d k 7 8 local control - to direction DA WNW ARDS g r o n 6 i r i w 5 w h f c 4 i o h 3 e w M l 2 p Control inputs could be supplied from a phase cable (L) or 1 m a neutral cable (N). Make a choose of one control option for x E all inputs. L NProgramming time of enclose During assembly of controller should be take special care 1. Press and hold a button PROG for time when green LED U start to Wrong connection could cause to give a shock and/or pulsate. break controller or connected device 2. When we again press a button PROG (ST AR T). Controller start count a time which is to signal by pulsate of green LED. 3. Press again a button PROG (ST OP). Controller remember a 4. Choose control option (control impulse L or N). Switch of local counted time. Programmin mode is automaticly closed ( green LED U control and central control connect with marks with function to joint to shine continually). choosen cable (accordance with choosen control option - L or N). * If at time 30 sec from start programming mode a count of time doesnt to start, then controller will out from All control inputs of controllers which works separately or programming mode. in group should have to common control impulse option - * Max time for programming 10min. T est by long time than all are controlling from the same phase, e.g. only L1 or all 10 min to cause controller automaticly out from from N. programming mode. * Input to programming mode posible is only when motor of roller is OFF . * In programming mode a controller doesnt to react for Choosing control option from phase (L) to control inputs outward control signal . should be connect to the same phase as for supply e.g. only phase L1. ASSEMBL Y 1. T ake OFF the power . Connection different phase e.g.L1 and L2 or phase L 2. Put on the controller on the wall or a roller box. andzer N to inputs of control inputs of controller can cause to wrong work of system and break controllers. Do not install to device which is broken or incomplete. 5. Controlled roller motor connect properly to joints 3 and 4 and to N. 6. T ake ON the power . 7. Programming to time of upwards/downwards of roller . Prescribed is 3. Connect power cable to joint 1-2 with marks. that programmed time should be longer t han 10 sec from real time of upwards/downwards. Group of controllers which working with common central control should be supplied from the same phase e.g only L1. TECHNICAL DA T A supply 230V AC current load AC-3 <2A control pulse current for L/N <1mA power supply indicator LED green power consumption 1W working temperature -25 50 C connection signal 4DY 1mm, l=10cm supply 4DY 1,5mm, l=10cm dimensions 55, h=13mm fixing under plaster box 60 A090727