FTLX1475D3BCL Finisar

Product Specification RoHS-6 Compliant 10Gb/s 10km 1310nm Single Mode Datacom SFP+ Transceiver FTLX1475D3BCL PRODUCT FEATURES Hot-pluggable SFP+ footprint Supports 9.95 to 10.5 Gb/s bit rates Power dissipation < 1W RoHS-6 compliant (lead-free) Commercial temperature range -5C to 70C Single 3.3V power supply Maximum link length of 10km Uncooled 1310nm DFB laser Limiting electrical interface APPLICATIONS receiver. Duplex LC connector 10GBASE-LR/LW 10G Ethernet Built-in digital diagnostic functions 1200-SM-LL-L 10G Fibre Channel Finisars FTLX1475D3BCL 10Gb/s Enhanced Small Form Factor Pluggable SFP+ transceivers are designed for use in 10-Gigabit Ethernet links up to 10km over Single Mode 1 2 fiber. They are compliant with SFF-8431 , SFF-8432 and IEEE 802.3ae 10GBASE- 3 4 LR/LW , and 10G Fibre Channel 1200-SM-LL-L . Digital diagnostics monitoring is 5 available via a 2-wire serial interface, as specified in SFF-8472 . The FTLX1475D3BCL employs a limiting receiver. 6 The optical transceiver is compliant per the RoHS Directive 2011/65/EU . See 7 Finisar Application Note AN-2038 for more details . PRODUCT SELECTION FTLX1475D3BCL Finisar Corporation, April 2017 Rev. B1 Page 1 FTLX1475D3BCL Product Specification I. Pin Descriptions Pin Symbol Name/Description Ref. 1 V Transmitter Ground. 1 EET 2 T Transmitter Fault. 2,3 FAULT 3 T Transmitter Disable. Laser output disabled on high or open. 4 DIS 4 SDA 2-wire Serial Interface Data Line. 2 5 SCL 2-wire Serial Interface Clock Line. 2 6 MOD ABS Module Absent. Grounded within the module. 5 7 RS0 Rate Select 0. Not Used. 5 8 RX LOS Loss of Signal indication. Logic 0 indicates normal operation. 6 9 RS1 Rate Select 1. Not Used. 10 V Receiver Ground. 1 EER 11 V Receiver Ground. 1 EER 12 RD- Receiver Inverted DATA out. AC Coupled. 13 RD+ Receiver Non-inverted DATA out. AC Coupled. 14 V Receiver Ground. 1 EER 15 V Receiver Power Supply. 7 CCR 16 V Transmitter Power Supply. 7 CCT 17 V Transmitter Ground. 1 EET 18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. 19 TD- Transmitter Inverted DATA in. AC Coupled. 20 V Transmitter Ground. 1 EET Notes: 1. Circuit ground is internally isolated from chassis ground. 2. Open collector/drain output, which should be pulled up with a 4.7k 10k Ohms resistor on the host board if intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V. 3. A high output indicates a transmitter fault caused by either the TX bias current or the TX output power exceeding the preset alarm thresholds. A low output indicates normal operation. In the low state, the output is pulled to <0.8V. 4. Laser output disabled on T >2.0V or open, enabled on T <0.8V. DIS DIS 5. Internally pulled down per SFF-8431 Rev 4.1. 6. LOS is open collector output. Should be pulled up with 4.7k 10k on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation logic 1 indicates loss of signal. 7. Internally connected. VeeT 20 1 VeeT TD- 19 2 TX Fault TD+ 18 TX Disable 3 VeeT 17 4 SDA VccT 16 5 SCL Towards Towards VccR 15 Bezel 6 MOD ABS ASIC VeeR 14 7 RS0 RD+ 13 8 RX LOS RD- 12 9 RS1 VeeR 11 10 VeeR Figure 1. Diagram of Host Board Connector Block Pin Numbers and Names. Finisar Corporation, April 2017 Rev. B1 Page 2