858-003-01F Glenair

Mighty Mouse Connectors with Size 8 Quadrax, Twinax, Coax or Power Contacts 858-003 and 858-004 Size 8 El Ochito Contacts for CAT 6a Cable Size 8 El Ochito contacts for 10g Base-T Cat 6a ethernet 4 pair cable El Ochito contacts accept PIC E6A3826 cable. These snap-in, rear release contacts K fit Glenair Series 80 Mighty Mouse connectors and Glenair MIL-DTL-38999 Series I, III and IV connectors with size 8 cavities. Crimp termination. Gold-plated copper alloy, Fluoropolymer insulator. 100 Ohms nominal, 500 Vrms DWV, 5000 MegOhms min at 200 VDC. Supplied unassembled. Sealing boot can be ordered with contact or separately. Fig. 1 Part Number Pin Contact Cable Part Number Fig. Description Contact and Accommodation Only 858-003 Sealing Boot Fig. 1 Pin PIC E6A3826 858-003-01 858-003-01F Fig. 2 Socket PIC E6A3826 858-004-01 858-004-01F Fig. 3 Sealing Boot PIC E6A3826 687-643-8-2 687-643-8-2 Fully Assembled Contact Shown for Reference Only .92 (23.37) Max .276 (7.01) Polarization Hex Crimp .060 (1.52) .271 (6.88) Key Fig. 2 1 2 Socket Contact .219 (5.56) 8 Hex) 858-004 .217 (5.51) 3 7 4 6 .033 (.84) 5 Cable Jacket Shown .029 (.74) For Reference Only .305 (7.75) .316 (8.03) 858-003 .295 (7.49) .313 (7.95) .060 .77 (19.56) Max Polarization Key .276 (7.01) (1.52) .271 (6.88) 1 Hex Crimp 2 8 3 Hex) 7 4 Fig. 3 .288 Cable Jacket Shown 6 5 (7.36) for Reference Only .033 (.84) Sealing Boot .284 .029 (.74) .631(16.03) 687-643 858-004 (7.21) .625 (15.88) .316 (8.03) .313 (7.95) Contact Removal Tool Sealing Boot Ref Cable Ref. Cable Plastic tool extracts wired contact from If sealing boot is used, slide boot onto Part Number Dia. (in.) Dia. (mm.) connector. First, remove sealing boot, wire before terminating contact. After .220 5.59 687-643-8-2 then insert tool from rear of connector. contact is installed in connector, slide boot forward into connector grommet Part Military Part to seal the contact cavity. Size Number Number 8 859-049 M81969/14-12 .336 (8.53 mm) .930 (23.6 mm) Max Dimensions in Inches (millimeters) are subject to change without notice.Dimensions in Inches (millimeters) are subject to change without notice. Rev. 08.04.15 2014 Glenair, Inc. Series 80 Mighty Mouse U.S. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. 1211 AIR WAY GLENDALE, CA 91201-2497 818-247-6000 FAX 818-500-9912 www.glenair.com K-33 E-Mail: sales glenair.com Mighty Mouse with 8 ContactsMighty Mouse with 8 Contacts Mighty Mouse Connectors with Size 8 Quadrax, Twinax, Coax or Power Contacts Size 8 El Ochito Contacts for CAT 6a Cable Material and Finish Specifications Inner Contact, Current Rating 1 A Copper alloy, 50 Outer Contact, Insulation Resistance 5000 Meg Ohms minimum microinches gold over Inner Ferrule, Crimp K Dielectric Withstanding Voltage 500Vrms Min sea Level nickel Sleeve Temperature Range -55 C to +175C Insulator Fluoropolymer Durability >500 cycles Sealing Boot Rigid Ultem Corrosion 48 Hrs Salt Spray Dielectric Vibration IAW AS39029/113 Sealing Boot Fluorosilicone Thermal Shock -55 C to +175 C Grommet Termination tools for size 8 coax contacts for PIC E6A3826 cable M22520/2-01 crimper for inner contact. Positioner, Daniels P/N K1906. Use with A A Requires B positioner, ordered separately. B crimper, ordered separately. Positioner holds A Length is 6.75 inches, weight is approx. 10 oz. contact at proper depth. Parallel action tool terminates outer contact. Die set for terminating outer contact and C Use with D hex crimp dies. 11 inches OAL, D cable shield. Two closures .231(5.87) hex 2.0 pounds. Anodized aluminum frame, steel closure for cable shield and Requires C crimp tool B mechanism, plastic handles. Accepts all M22520/5 sold separately. Hardened steel, black oxide finish. die sets. D Military Part Daniels Part Figure Part Number Number Number A 809-015 M22520/2-01 AFM8 B 859-101 None K1906 C C 809-129 M22520/5-01 HX4 D 859-047 M22520/5-45 N/A About Sealing Boots The sealing boot is necessary to prevent moisture and contamination from penetrating the connector. The sealing boot is ordered separately. The boot consists of a rigid dielectric sleeve and a fluorosilicone rubber grommet. Slide boot onto cable before terminating contact. After the contact is installed into connector, seat the boot into connector grommet. Connector Grommet Sealing Boot Dimensions in Inches (millimeters) are subject to change without notice. 2014 Glenair, Inc. Series 80 Mighty Mouse U.S. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. 1211 AIR WAY GLENDALE, CA 91201-2497 818-247-6000 FAX 818-500-9912 www.glenair.com K-34 E-Mail: sales glenair.com