Optical and Mechanical Encoders Specifications are subject to change. Please refer to the current datasheet on www.grayhill.com for the most current published specifications for this product. Optical Encoders SERIES 62B Push-Pull, High Torque FEATURES Multiple Switching Functions Available Pin, Cable and Connector with Cable in One Compact Device Termination Options Push and Pull Travel Options Custom Modifications Available Pull Shaft Resists Accidental APPLICATIONS Actuation Use for Menu Scrolling or High Rotational Torque for Positive Function Selection Detent Feel and Superior Tactile Avionics Feedback Industrial Long Life, High Reliability Medical CMOS, HCMOS, and TTL Compatible DIMENSIONS in inches (and millimeters) Connector Version Pinned Version Stripped Version .430 SHAFT-DETENT POSITION CHART .350 (10,92) (8,89) POS DIM (.050 SPC X 7) DIM 16 11.25 SEE CHART 32 5.625 .219.004 (5,560,1) *SHAFT SHOWN IN A DETENT POSITION 1.183.015 .687 .500 .400 (30,050,38) (17,45) .250.001) (12,7) (10,16) (6,350,02) 4.000.20 .312 CONNECTOR IS (7,92) 3/8-32 UNEF-2A .707 AMP P/N 215083-8 (17,96) THREAD OR EQUIVALENT .335 .395.015 .250.004 (8,51) (10,030,38) (6,350,1) Suggested Mounting Panel Cutout 1.045 (26,54) .161.002 1.080.015 4,090 ,05 (27,430,38) .380.003 9,650,07 .110 (2,79) XXX.20 .100 SEE ORDERING INFO (2,54) *TOLERANCES.010 U.O.S057.002 1,450 ,05 SWITCH SCHEMATIC, WAVEFORM, AND TRUTH TABLE 8 POWER (5V) R* 7 OUTPUT A R* 6 OUTPUT B PULLBUTTON 5 4 PULLBUTTON 3 PUSHBUTTON 2 PUSHBUTTON 1 GROUND *EXTERNAL 2.2k PULL-UP RESISTANCE REQUIRED FOR OPERATION. Grayhill, Inc. 561 Hillgrove Avenue LaGrange, Illinois 60525-5997 USA Phone: 708-354-1040 Fax: 708-354-2820 www.grayhill.comOptical and Mechanical Encoders Specifications are subject to change. Please refer to the current datasheet on www.grayhill.com for the most current published specifications for this product. Optical Encoders WAVEFORM AND TRUTH TABLE Standard Quadrature 2-Bit Code Clockwise Rotation HIGH Position Output A Output B OUTPUT 1 LOW 2 HIGH 3 OUTPUT LOW 4 1 2 3 4 5 6 POSITION NUMBER Indicates logic high blank indicates logic low. Code repeats every 4 positions. SPECIFICATIONS over Nickel Environmental Specifications Mounting Torque: 15 in-oz maximum 0 0 Infrared Light Emitting Diode Chips: Gal- Operating Temperature Range: -40 C to 85 Shaft Push-Out Force: 45 lbs minimum lium Aluminum Arsenide C Shaft Pull-Out Force: 20 lbs minimum 0 0 Silicon Phototransistor Chips: Gold and Storage Temperature Range: -55 C to 100 C Terminal Strength: 15 lbs minimum Humidity: 96 hours at 90-95% humidity Aluminum Alloys terminal pull-out force for cable or header 0 Resistor: Metal Oxide on Ceramic Substrate at 40 C termination Solder Pins: Brass, Plated with Tin Mechanical Vibration: Harmonic motion with Solderability: 95% free of pin holes and Code Rotor: Delrin 100 amplitude of 15 g, within a varied frequency of voids Code Housing: Hiloy-610 10 to 2000 Hz Mechanical Shock: Pull Dome Retainer: Ryton R-4 Pull-Button/Push-Button Electrical Pull Actuator: Polyurethane, Isoplast 101 Test 1: 100 g for 6 ms half-sine wave with a and Mechanical Specifications LGF40 Blk velocity change of 12.3 ft/sec Rating: 10 mA at 5 Vdc Cover: Ryton R-4 Test 2: 100 g for 6 ms sawtooth wave with a Contact Resistance: <10 ohms Cable: Copper Standard with Topcoat in velocity change of 9.7 ft/sec Life: 3 million actuations minimum PVC Insulation (Cabled Versions Only) Contact Bounce: <4 ms make,<10 ms Connector: PA4.6 with Tin over Nickel Rotary Electrical and break Plated Phosphor Bronze (Cable/Connector Mechanical Specifications Actuation Force: 1700450 g for both push Versions) Operating Voltage: 5.00.25 Vdc and pull-button Label: TT406 Thermal Transfer Cast Film Supply Current: 30 mA maximum at 5 Vdc Shaft Travel: .030.010 standard travel. Solder: Sn/Ag/Cu, lead-free, no clean Output: Open collector phototransistor, exter- .050.010 long travel Lubricating Grease: Nye Nyogel 774L nal pull-up resistors are required Mounting Hex Nut: Tin/Zinc Over 1/2 Hard Output Code: Two-bit quadrature, channel Materials and Finishes Brass 0 A leads channel B by 90 electrically during Bushing: Zinc Diecast, Cadmium Plated per Lockwasher: 8-18 Stainless Steel, Passiv- clockwise rotation of the shaft QQP-416, Class II, Type II ate Finish Logic Output Characteristics: Shaft: Aluminum Pin Header: Hi-Temp Glass Filled Thermo- Logic high signal shall be no less Detent Cover: Powered Metal per plastic UL94V-0, Phosphor Bronze (Pinned than 3.0 Vdc SS-316N1-25 Versions Only) Logic low signal shall be no greater Through Bolts: 305 Stainless Steel than 1.0 Vdc Through Bolts Nuts: 305 Stainless Steel Minimum Sink Current: 2.0 mA Shaft Travel Springs: Carbon Steel, Power Consumption: 150 mW maximum Oil Dip Finish Mechanical Life: 1 million rotational cycles of Detent Ball: Stainless Steel operation. One cycle is a rotation through all Detent Spring: Tinned Music Wire positions and a full return Spacer/Push Dome Retainer: Ryton R-4 Average Rotational Torque: 16 position: Push Actuator: Zytel 70G33L 5.0 1.5 in-oz, 32-position: 2.5 1 .5 in-oz. Snap Dome: Stainless Steel Torque shall be within 50% of initial value Printed Circuit Boards: Nema Grade FR4, throughout life Double Clad with Copper, Plated with Gold ORDERING INFORMATION Series 0 Angle of Throw: 22 = 22.5 For Code Change and 16 Detent Positions. 0 11 = 11.25 For Code Change and 32 Detent Positions. Push/Pull-Button Travel: S = Standard Travel (.030 Both Directions). L = Long Travel (.050 Both Directions) Push/Pull Option: P = Pull-Button Only. PP = Push and Pull-Button Termination: C = .050 Pitch Ribbon Cable with Connector 62BXX-XXX-040X S = .050 Pitch Ribbon Cable with Stripped End P = .050 Pitch Pin Header Cable Termination: 040 = 4.0in. Cable is terminated with Amp Connector P/N 215083-6. See Amp Mateability Guide for mating connector details. *Eliminate cable length if ordering pins (Ex: 62B22-SP-P) Grayhill, Inc. 561 Hillgrove Avenue LaGrange, Illinois 60525-5997 USA Phone: 708-354-1040 Fax: 708-354-2820 www.grayhill.com