GLS85LS1002A/1004A/1008B/1016B/1032B/1064B Industrial / Commercial Temp SATA NANDrive Fact Sheet 04.000 October 2016 Features Industry Standard Serial ATA (SATA) Host Interface Expanded Data Protection 1) - Added data security through user-selectable - SATA 1.5 Gb/s or SATA 3.0 Gb/s protection zones - ATA/ATAPI-8 compliant Integrated Voltage Detector - Supports 48-bit address feature set - Detects supply voltage fluctuations and Performance generates reset during power-up and power- - Sequential data read - down to prevent inadvertent writes Up to 110 MByte/sec* Supports SMART Commands - Sequential data write - Up to 60 MByte/sec* 20-Byte Serial Number * measured using 128 KByte transfer size - Factory pre-programmed 10-Byte unique ID Power Management - User-programmable 10-Byte ID - 3.3V and 1.2Vpower supply Robust Built-in ECC - Host SATA interface power management NAND Configuration - Immediate disabling of unused circuitry - 2 bits per cell (MLC) without host intervention Temperature Range 2) Power Specifications - Commercial: 0C to 70C - Active mode: - Industrial: -40C to 85C 820mW typical (GLS85LS1064B) FBGA package 565mW typical (GLS85LS1032B) - 14.0 mm x 24.0 mm x 1.95 mm, 145-ball, 440mW typical (GLS85LS1016B) 1.0 mm ball pitch, FZJE 360mW typical (GLS85LS1008B) All Devices are RoHS Compliant 360mW typical (GLS85LS1004A) 1) Current product revision supports SATA Revision 1.x with 360mW typical (GLS85LS1002A) host transfer rate of up to 1.5 Gb/s (i.e. SATA 1.5 Gb/s). - Idle / Standby mode: 210mW typical SATA 3.0 Gb/s refers to SATA Revision 2.x and will be supported by our planned future product revisions. - Sleep mode: 70mW typical 2) For management of the Sleep Mode, refer to SATA NANDrive Application Design Guide. Product Description The GLS85LS1002A / 1004A / 1008B / 1016B / The integrated NAND flash controller with built-in 1032B / 1064B Industrial Temperature and advanced NAND management firmware Commercial Temperature SATA NANDrive devices communicates with the host through the standard (referred to as SATA NANDrive in this datasheet) SATA protocol. It does not require any additional or are fully integrated solid state drives. They combine proprietary software such as the Flash File System an advanced Greenliant NAND controller and 2, 4, 8, (FFS) and Memory Technology Driver (MTD). 16, 32 or 64 GByte of NAND flash in a multi-chip SATA NANDrive is pre-programmed with a 10-Byte package. These products are ideal for embedded and unique serial ID and has the option of programming portable applications that require smaller form factor an additional 10-Byte serial ID for even greater and more reliable data storage. system security. SATA-interface solid state mass storage technology is SATA NANDrives advanced NAND management widely used in portable and industrial computers, set- technology enhances data reliability and security, top boxes, multi-functional printers, point-of-sales improves endurance and accurately estimates the terminals, video and audio recorders, medical remaining life of the NAND flash devices. This instruments and car infotainment systems. innovative technology combines robust NAND SATA NANDrive is a single device, solid state drive controller hardware error correction capabilities with (SSD) that provides the functionality and compatibility advanced wear-leveling algorithms and bad block of a complete SATA hard disk drive (HDD) in a 14 mm management to significantly extend the life of the x 24 mm BGA package for easy, space saving product. mounting to a system motherboard. These products SATA NANDrive devices are offered in a 145-ball surpass traditional storage in their small size, security, BGA, 1 mm ball pitch package. reliability, ruggedness and low power consumption. These specifications are subject to change without notice. 10/12/2016 2016 Greenliant Systems 1 S71430-F GLS85LS1002A/1004A/1008B/1016B/1032B/1064B Industrial / Commercial Temp SATA NANDrive Fact Sheet 04.000 October 2016 1.0 GENERAL DESCRIPTION Each SATA NANDrive contains an integrated SATA NAND flash memory controller and up to eight discrete NAND flash die in a BGA package. Refer to Figure 2-1 for the SATA NANDrive block diagram. 1.1.5 Error Correction Code (ECC) 1.1 Optimized SATA NANDrive High performance is achieved through optimized The heart of SATA NANDrive is the SATA NAND flash hardware error detection and correction. memory controller which translates standard SATA signals into flash media data and control signals. The 1.1.6 Serial Communication Interface (SCI) following components contribute to SATA NANDrives The Serial Communication Interface (SCI) is designed operation. for error reporting. During the product development 1.1.1 Microcontroller Unit (MCU) stage, it is recommended to provide the SCI port on the PCB to aid in design validation. The MCU translates SATA commands into data and control signals required for flash media operation. 1.1.7 Multi-tasking Interface 1.1.2 Internal Direct Memory Access (DMA) The multi-tasking interface enables fast, sequential write performance by allowing concurrent Read, SATA NANDrive uses internal DMA allowing instant Program and Erase operations to multiple flash media. data transfer from/to buffer to/from flash media. This implementation eliminates microcontroller overhead associated with the traditional, firmware-based 1.2 SMT Reflow Consideration approach, thereby increasing the data transfer rate. The SATA NANDrive family utilizes standard NAND 1.1.3 Power Management Unit (PMU) flash for data storage. Because the high temperature in a surface-mount soldering reflow process may alter The PMU controls the power consumption of SATA the content on NAND flash, it is recommended to NANDrive. The PMU dramatically reduces the power program SATA NANDrive after the reflow process. consumption of SATA NANDrive by putting the part of 3) the circuitry that is not in operation into sleep mode. 1.3 Advanced NAND Management The Flash File System handles inadvertent power SATA NANDrives integrated controller uses interrupts and has auto-recovery capability to ensure advanced wear-leveling algorithms to substantially SATA NANDrive firmware integrity. For regular power increase the longevity of NAND flash media. Wear management, the host must send an caused by data writes is evenly distributed in all or IDLE IMMEDIATE command and wait for command select blocks in the device that prevents hot spots in ready before powering down SATA NANDrive. locations that are programmed and erased extensively. 3) For management of the Sleep Mode, refer to SATA This effective wear-leveling technique results in NANDrive Application Design Guide. optimized device endurance, enhanced data retention and higher reliability required by long-life applications. 1.1.4 Embedded Flash File System The embedded flash file system is an integral part of SATA NANDrive. It contains MCU firmware that performs the following tasks: 1. Translates host side signals into flash media writes and reads 2. Provides flash media wear leveling to spread the flash writes across all memory address space to increase the longevity of flash media 3. Keeps track of data file structures 4. Manages system security for the selected protection zones These specifications are subject to change without notice. 10/12/2016 2016 Greenliant Systems 2 S71430-F