CHECKTEMP Hanna

Checktemp 1 Checktemp 1 Checktemp 1 Checktemp 1 C C C C C: Celsius Model SPECIFICATIONS:SPECIFICATIONS:SPECIFICATIONS:SPECIFICATIONS:SPECIFICATIONS: Checktemp 1 C/N C/N C/N C/N C/N: Celsius Model with Factory Calibration Certificate RangeRangeRangeRangeRange F F Checktemp 1 F F F: Fahrenheit Model Checktemp 1 C C C C C -50.0 to 150.0C Checktemp 1 F/N F/N F/N F/N F/N: Fahrenheit Model with Factory Calibration Certificate Checktemp 1 F F F F F -58.0 to 302F ResolutionResolutionResolutionResolutionResolution Checktemp 1 C C C C C 0.1C Checktemp 1 F F F 0.1F (-58.0 to 199.9F) F F 1F (200 to 302F) AccuracyAccuracyAccuracyAccuracyAccuracy ( 20C/68F)( 20C/68F)( 20C/68F)( 20C/68F)( 20C/68F) Checktemp 1 C C C C C 0.3C (-20 to 90C) 0.5C (outside) Checktemp 1 F F F 0.5F (-4 to 194F) F F 1F (outside) Typical EMCTypical EMCTypical EMCTypical EMCTypical EMC DeviationDeviationDeviationDeviationDeviation C C Checktemp 1 C C C 0.3C Checktemp 1 F F F F F 0.5F EnvironmentEnvironmentEnvironment 0 to 50C (32 to 122F) EnvironmentEnvironment 95% RH max. Battery TypeBattery TypeBattery TypeBattery TypeBattery Type 1 x 1.4V alkaline LifeLife LifeLifeLife approx. 3,000 hours of continuous use DimensionsDimensions DimensionsDimensionsDimensions 106 x 58 x 19 mm (4.2 x 2.2 x 0.7 ) WeightWeightWeightWeightWeight 80 g (2.8 oz.) ProbeProbe ProbeProbeProbe Stainless steel, 160mm x 3mm with 1 meter (3.3 ) cableC Checktemp 1 Checktemp 1 Checktemp 1 OPERATION:OPERATION:OPERATION:OPERATION:OPERATION: 0.0C 0.3C battery cover and change the RUN ON MEASUREMENT or 32F 0.5F. 1.4V AAA battery, paying atten- Turn Checktemp 1 on. ON MODE RUN TEST OFF 0C/32F Contact your tion to its polarity. Replace the Dip Checktemp1 probe CALIBRATION TEST OFF 0C/32F BATTERY 1.5V AAA CHECK dealer or your cover and tighten the two screws. MODE in sample. An im- BATTERY 1.5V AAA nearest Han- Battery should only be replaced mersion level of 4 na Service in a safe area using the battery cm (1) is rec- Center for type specified in this instruction ommended. recalibration, if necessary. Move sheet. Do NOT immerse the Cal-check switch back up. The SUGGESTIONS FOR USERS:SUGGESTIONS FOR USERS:SUGGESTIONS FOR USERS:SUGGESTIONS FOR USERS:SUGGESTIONS FOR USERS: the probe handle. Before using this product, make sure that it is entirely display returns to measurement Do NOT wrench suitable for the environment in which it is used. mode. Operation of this instrument in residential areas could the probe or put cause interference to radio and TV equipment. Any BATTERY REPLACEMENT:BATTERY REPLACEMENT:BATTERY REPLACEMENT:BATTERY REPLACEMENT:BATTERY REPLACEMENT: variation introduced by the user to the supplied heavy objects on the cable. If equipment may degrade the instrument s EMC When the Checktemp 1 cannot be the cable is damaged, the meter performance. To avoid electrical shocks, do not use this instrument when voltage at the measurement switched on or the display fades, needs to be replaced. surface exceeds 24VAC or 60 VDC. To avoid damage remove the two screws, open the or burns, do not perform any measurement in Wait for a few seconds for the microwave ovens. display to stabilize and switch the meter off when not in use. Variations in readings or fading RUN ON RUN ON Visit Visit Visit Visit Visit our our our our our Internet Internet Internet Internet Internet Home Home Home Home Home Page:Page:Page:Page:Page: display can indicate a weak battery.