Dear Customer, Instruction Manual FUNCTIONAL DESCRIPTIONFUNCTIONAL DESCRIPTIONFUNCTIONAL DESCRIPTIONFUNCTIONAL DESCRIPTIONFUNCTIONAL DESCRIPTION GENERAL DESCRIPTIONGENERAL DESCRIPTIONGENERAL DESCRIPTION GENERAL DESCRIPTIONGENERAL DESCRIPTION Thank you for choosing a Hanna product. This manual will provide you with the necessary information for the correct HI147-00 operation of the meter. Please read it carefully before using These thermometers are specially designed with a food com- HI147-01 the meter. If you need additional technical information, do patible silicone cable, and can be used for continuous not hesitate to e-mail us at tech hannainst.com. Check-fridge thermometers monitoring of temperature in food care areas. These instruments are in compliance with the directives. Simply attach the meter to outside a fridge or metal cabinet. This is possible thanks to the two magnets located on the back of the unit. The probe can then be inserted inside the PRELIMINARY EXAMINATIONPRELIMINARY EXAMINATIONPRELIMINARY EXAMINATION PRELIMINARY EXAMINATIONPRELIMINARY EXAMINATION cabinet or fridge for continuous temperature monitoring. A switch allows a rapid check of the meter calibration at any Remove the instrument from the packing material and ex- time. amine it carefully. If any damage has occurred during shipment, immediately notify your Dealer or the nearest Two models are available: Hanna Customer Service Center. HI 147-00 displays temperatures in Centigrade degrees The meters are supplied with 1 x 1.5V AAA battery. HI 147-01 displays temperatures in Fahrenheit degrees. Note: Conserve all packing material until the instrument has 1. Liquid Crystal Display (LCD) been observed to function correctly. Any defective item 2. ON/OFF switch must be returned in its original packing. 3. Food compatible silicone cable 4. Temperature probe Hanna Instruments reserves the right to modify the design, construction These Instruments are in 5. TEST/READ switch and appearance of its products without advance notice. Variations in readings or fading display can indicate a low OPERATIONAL GUIDEOPERATIONAL GUIDEOPERATIONAL GUIDE CE DECLARATION OF CONFORMITYCE DECLARATION OF CONFORMITYCE DECLARATION OF CONFORMITYCE DECLARATION OF CONFORMITYCE DECLARATION OF CONFORMITY SPECIFICATIONSSPECIFICATIONSSPECIFICATIONSSPECIFICATIONSSPECIFICATIONS OPERATIONAL GUIDEOPERATIONAL GUIDE battery level. Recommendations for Users Before using these products, make sure TAKING MEASUREMENTS HI 147-00 that they are entirely suitable for the environment in which they are used. Op- Turn the meter ON and select READ on the TEST/READ eration of these instruments in residential Range -50.0 to +150.0C areas could cause unacceptable interfer- BATTERY REPLACEMENTBATTERY REPLACEMENTBATTERY REPLACEMENTBATTERY REPLACEMENTBATTERY REPLACEMENT ences to radio and TV equipment. Any switch. Resolution 0.1C variation introduced by the user to the supplied equipment may degrade the The temperature value will be displayed on the LCD. Accuracy ( 25C/77F) 0.3C (-20 to 90C) instruments EMC performance. To avoid When the display fades, remove the two screws on the back. electrical shock, do not use these instru- Wait for a few seconds for the reading to stabilize. ments when voltages at the measure- 0.5C (outside) Remove the cover and replace the 1.5V AAA battery while ment surface exceed 24 VAC or 60 VDC. To avoid damages or burns, do not per- Typical EMC Deviation 0.5C form any measurement in microwave ov- paying attention to its polarity. ens. HI 147-01 CALIBRATION CHECK Range -58.0 to +302F Select TEST on the TEST/READ switch. If the meter is cali- Resolution 0.1F (-58.0 to 199.9F), 1F (200 to 302F) brated, the display will stabilize and show 0.0 (HI 147-00) Accuracy ( 25C/77F) 0.5F (-4 to 194F) or 32.0 (HI 147-0) in a few seconds. To return to mea- 1F (outside) WARRANTYWARRANTYWARRANTYWARRANTYWARRANTY surement mode, move the TEST/READ switch back to READ. Typical EMC Deviation 1F Contact your dealer or your nearest Hanna Service Center for HI 147-00 and HI 147-01 are warranted for one year against defects in workmanship and materials when used for its intended purpose and maintained according to instructions. This recalibration, if necessary. warranty is limited to repair or replacement free of charge. Common specifications Damages due to accident, misuse, tampering or lack of prescribed maintenance are not covered. Probe Stainless steel probe with 1m silicone cable If service is required, contact the dealer from whom you purchased the instrument. If under warranty, Replace the cover and tighten the two screws. report the model number, date of purchase, serial number and the nature of the failure. If the repair is not covered by the warranty, you will be notified of the charges incurred. If the instrument is to be Battery Type/Life 1 x 1.5V AAA Notes:Notes:Notes:Notes:Notes: returned to Hanna Instruments, first obtain a Returned Goods Authorization Number from the Battery should be replaced only in a safe area using the Customer Service department and then send it with shipment costs prepaid. When shipping any typical 3 years of continuous use Do NOT wrench the probe or put heavy objects on the instrument, make sure it is properly packaged for complete protection. battery type specified in this instruction sheet. To validate your warranty, fill out and return the enclosed warranty card within 14 days from the Dimensions 93 x 39 x 31mm (3.7 x 1.5 x 1.2) cable. If the cable is damaged, the meter needs to be date of purchase. Weight 60g (2.1oz) replaced. All rights are reserved. Reproduction in whole or in part is prohibited without the written consent of the copyright owner, Hanna Instruments Inc., Woonsocket, Rhode Island, 02895 , USA. 09/2000 - R1