TechnicalData Sheet BERGQUIST BOND PLY TBP 800 Known as BERGQUIST BOND-PLY 800 October -2018 PRODUCT DESCRIPTION Adhesion Properties Thermally Conductive, Fiberglass Reinforced Pressure Lap Shear Strength 25 C , MPa 1.0 (1) Sensitive Adhesive Tape . ASTM D1002 (psi) ( 150 ) Technology Acrylic Electrical Properties Appearance Gray DielectricBreakdown Voltage ,ASTM D149: Reinforcement Carrier Fiberglass 0.005 (Vac) 4,000 TotalThickness 0.005,0.008 inch (0.127,0.203 mm ) 0.008 (Vac) 6,000 Application Thermal management, DielectricConstant ,ASTM D150 1,000 Hz 4.0 Thermally conductive adhesive 11 Volume Resistivity ,ASTM D257,ohm-meter 110 Operating Temperature -40 to 125 C Range Thermal Properties Thermal Conductivity ,ASTM D5470,W/(m-K) 0.8 FEATURES AND BENEFITS 2 Thermal impedance: 0.6C-in /W 50 psi Thermal Performance vs. Pressure Highbond strength to most epoxies and metals TO-220 Thermal Performance ,C/W : Double-sided, pressure sensitive adhesive tape 0.005 : Highperformance, thermally conductive acrylic adhesive 10 psi 5.0 More cost-effective than heat-cure adhesive, screw 25 psi 5.0 mounting or clipmounting 50 psi 4.8 TYPICAL APPLICATIONS 100 psi 4.3 Mount LEDassembly to troffer housing 200 psi 4.2 Mount LEDassembly to heat sink Mount heat spreader onto power converter PCB or onto 0.008 : motor control PCB 10 psi 6.2 Mount heat sink onto BGA graphic processor or drive 25 psi 6.0 processor 50 psi 5.6 100 psi 5.3 BERGQUIST BOND PLY TBP 800 is a thermally conductive, 200 psi 5.2 electricallyisolating double- sided tape . BERGQUIST BOND PLY TBP 800 is utilized in lightingapplications that require 2 (2) Thermal Impedance ,ASTM D5470,C-in /W : thermal transfer and electric isolation. 0.005 : Highbond strengths obtained at ambient temperature lead to 10 psi 0.63 significant processing cost savings in labor, materials and 25 psi 0.62 throughput due to the elimination ofmechanical fasteners and 50 psi 0.6 hightemperature curing. 100 psi 0.58 200 psi 0.57 TYPICAL PROPERTIES Physical Properties 0.008 : Elongation,45 to warp and fill,ASTM D412,% 70 10 psi 0.78 CoefficientofThermal Expansion, ASTM D 3386, 600 25 psi 0.74 ppm/C 50 psi 0.72 Flammability Rating, UL 94 V-0 100 psi 0.71 Tensile Strength MPa 10 200 psi 0.71 (psi) ( 1,500)TDS BERGQUIST BOND PLY TBP 800, October -2018 1) Tested per ASTM D1002 with aluminum lap shear samples, 75 psi applied for 5 seconds be reliable.We cannot assume responsibility for the results obtained by others then pressure removed. 0.5 square inch BERGQUIST BOND PLY TBP 800 over whose methods we have no control. It is the user s responsibility to 2) The ASTM D5470 test fixture was used. The recorded value includes interfacialthermal determine suitability for the user s purpose ofany production methods mentioned resistance. These values are provided for reference only. Actual application performance is herein and to adopt such precautions as may be advisable for the protection of directly related to the surface roughness, flatness and pressure applied. property and ofpersons against any hazards that may be involved in the handling and use thereof. In lightof the foregoing,Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use GENERAL INFORMATION of Henkel Corporations products. Henkel Corporation specifically For safe handling information on this product, consult the Safety disclaims any liability for consequential or incidental damages of any kind, Data Sheet, (SDS). including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from Not for product specifications domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We The technicaldata contained herein are intended as reference recommend that each prospective user test his proposed application before only. Please contact your localquality department for repetitive use, using this data as a guide. This product may be covered by one or assistance and recommendations on specifications for this more United States or foreignpatents or patent applications. product. Trademark usage: Except as otherwise noted Alltrademarks in this document are trademarks and/or registered trademarks of Henkel and its affiliatesin the CONFIGURATIONS AVAILABLE U.S.and elsewhere. BERGQUIST BOND PLY TBP 800 are supplied in: Sheet form Reference 2 Rollform Die-Cut parts Conversions (C x 1.8)+ 32 = F kV/mm x 25.4 = V/mil mm /25.4 = inches N x 0.225 = lb/F N/mm x 5.71= lb/in psi x 145 = N/mm MPa = N/mm Nm x 8.851 = lbin Nm x 0.738= lbft Nmm x 0.142= ozin mPas = cP Disclaimer Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience ofthe product as at the date ofthis TDS. The product can have a variety of different applications as well as differingapplication and working conditions in your environment that are beyond our control. Henkel is, therefore, not liablefor the suitability ofour product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability ofour product. Any liabilityin respect ofthe information in the TechnicalData Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligenceand any liabilityunder any applicablemandatory product liabilitylaw. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: In case Henkel would be nevertheless held liable,on whatever legalground, Henkels liabilitywillin no event exceed the amount ofthe concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience ofthe product as at the date ofthis TDS. Henkel is, therefore, not liablefor the suitability ofour product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability ofour product. Any liabilityin respect ofthe information in the TechnicalData Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligenceand any liabilityunder any applicablemandatory product liabilitylaw. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnished for information only and are believed to Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.2891.8000 For the most direct access to local sales and technical support visit: www.henkel.com/electronics