Technical Data Sheet BERGQUIST GAP FILLER TGF 1500LVO Formerly known as GAP FILLER1500LV July -2018 PRODUCT DESCRIPTION TYPICAL APPLICATIONS A thermally conductive, liquidgap fillermaterial . Lighting Automotive electronics (HEV,NEV,batteries) Technology Silicone Silicone-sensitive electronics Appearance (cured) Yellow Appearance -Part A Yellow TYPICAL PROPERTIES OF UNCURED MATERIAL Appearance -Part B White Viscosity ,Highshear,Capillary,ASTM D5099,mPas (cP) : Cure Room temperature cure or Heat cure 3,000/ sec .Part A and B measured separately. 20,000 Application Thermal management, Density ,ASTM D792,g/cc 2.7 TIM(Thermal Interface Material) Working Time 25C ,Parallel plate rheometer, Mix Ratio by weight: 1 :1 see reactivity application note , 120 minutes Part A:Part B ShelfLife 25C ,days 180 Mix Ratio by volume: 1 :1 Part A:Part B TYPICAL CURE SCHEDULE SolidsContent, % 100 Cure Schedule Operating Temperature -60 to 200C 8 hours 25C Range 10 minutes 100C Parallel plate rheometer, see reactivity application note. FEATURES AND BENEFITS Thermal Conductivity: 1.8W/m-K The above cure profilesare guideline recommendations. Cure conditions (time and temperature) may vary based on Low volatility for silicone sensitive applications customers experience and their application requirements, as 100% solids-no cure by-products well as customer curing equipment, oven loading and actual Ultra- conforming, with excellent wet-out oven temperatures. Excellent low and high temperature mechanical and chemical stability TYPICAL PROPERTIES OF CURED MATERIAL Physical Properties BERGQUIST GAP FILLERTGF 1500LVO is a thermally Hardness, Shore 00,Thirty second delay value , 80 conductive, liquid gap fillingmaterial . Thismaterial offers the ASTM D2240 hightemperature resistance and low modulus of a silicone Heat Capacity ,ASTM D1269,J/g-K 1.0 material with significantly lower levels of silicone outgassing for use in silicone sensitive application. Flammability, UL94 V-0 Siloxane Content, D 4 -D10,ppm <100 The mixed system will cure at room temperature and can be accelerated with the addition of heat . As cured BERGQUIST Electrical Properties GAP FILLERTGF 1500LVO provides a soft, thermally Dielectric Strength ,ASTM D149,V/mil 400 conductive, form-in place elastomer that is ideal for fragile assemblies and fillingunique and intricate airvoids and gaps. Dielectric Constant ,ASTM D150 1,000 Hz 6.2 10 Volume Resistivity ,ASTM D257,ohm-meter 110 Liquid dispensed thermal materials offer infinite thickness Thermal Properties variations and impart little to no stress on sensitive Thermal Conductivity ,ASTM D5470,W/(m-K) 1.8 components during assembly . BERGQUIST GAP FILLER TGF 1500LVO exhibits low level natural tack characteristics and isintended for use in applications where a strong structural bond isnot required . GENERAL INFORMATION For safe handling information on this product, consult the Safety Data Sheet, (SDS).TDS BERGQUIST GAP FILLERTGF 1500LVO, July -2018 Not for product specifications Disclaimer The technical data contained herein are intended as reference Note: The information provided in this Technical Data Sheet (TDS) including the only. Please contact your local quality department for recommendations for use and application of the product are based on our assistance and recommendations on specifications for this knowledge and experience of the product as at the date of thisTDS.The product product. can have a variety of different applications as well as differingapplication and working conditions in your environment that are beyond our control. Henkel is, The above cure profilesare guideline recommendations. Cure therefore, not liablefor the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended conditions (time and temperature) may vary based on applications and results. We strongly recommend that you carry out your own customers experience and their application requirements, as prior trialsto confirm such suitability of our product. well as customer curing equipment, oven loading and actual Any liabilityin respect of the information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product isexcluded, oven temperatures. except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liabilityunder any applicablemandatory CONFIGURATIONS AVAILABLE product liabilitylaw. BERGQUIST GAP FILLERTGF 1500LVO isavailable in the In case products are delivered by Henkel Belgium NV, Henkel Electronic following configurations: Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: In case Henkel would be nevertheless held liable,on whatever legal ground, Cartridges Henkels liabilitywill in no event exceed the amount of the concerned delivery. Kits In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the Application: recommendations for use and application of the product are based on our Mixed and dispensed using dual tube cartridge packs with knowledge and experience of the product as at the date of thisTDS. Henkel is, therefore, not liablefor the suitability of our product for the production processes static mixers and a manual or pneumatic gun and conditions in respect of which you use them, as well as the intended Mixed and dispensed using industry standard highvolume applications and results. We strongly recommend that you carry out your own mixing and dispensing document prior trialsto confirm such suitability of our product. Any liabilityin respect of the information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product isexcluded, STORAGE except ifotherwise explicitly agreed and except in relation to death or personal Store product in the unopened container in a dry location. injury caused by our negligence and any liabilityunder any applicablemandatory Storage information may be indicated on the product container product liabilitylaw. labeling. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: Optimal Storage: 5 to 25C for a 6 month shelflife.Material The data contained herein are furnished for information only and are believed to removed from containers may be contaminated during use. Do be reliable. We cannot assume responsibility for the results obtained by others not return product to the original container. Henkel Corporation over whose methods we have no control. It is the user s responsibility to cannot assume responsibility for product which has been determine suitability for the user s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of contaminated or stored under conditions other than those property and of persons against any hazards that may be involved in the handling previously indicated. Ifadditional information is required, and use thereof. In light of the foregoing, Henkel Corporation specifically please contact your local Technical Service Center or disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use Customer Service Representative. of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, Conversions including lost profits. The discussion herein of various processes or compositions isnot to be interpreted as representation that they are free from (C x 1.8)+ 32 = F domination of patents owned by others or as a license under any Henkel kV/mm x 25.4 = V/mil Corporation patents that may cover such processes or compositions. We mm /25.4 = inches recommend that each prospective user test hisproposed application before Nx 0.225= lb repetitive use, using thisdata as a guide. Thisproduct may be covered by one or more United States or foreign patents or patent applications. N/mmx 5.71= lb/in Trademark usage: Except as otherwise noted Alltrademarks in thisdocument psi x 145 = N/mm are trademarks and/or registered trademarks of Henkel and its affiliatesin the MPa = N/mm U.S.and elsewhere. Nm x 8.851 = lbin Nm x 0.738= lbft Reference 1 Nmm x 0.142 = ozin mPas = cP Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.3898.4800 For the most direct access to local sales and technical support visit: www.henkel.com/electronics