Technical DataSheet BERGQUIST GAP PAD TGP 1300 Known as BERGQUIST GAP PAD 1500S30 November -2018 PRODUCT DESCRIPTION Physical Properties Highly Conformable, Thermally Conductive, Reinforced Hardness, Shore 00,Thirty second delay value , 30 S-Class Gap FillingMaterial. ASTM D2240,Bulkrubber Heat Capacity ,ASTM E1269,J/g-K 1.0 Technology Silicone Density ,Bulkrubber ,ASTM D792,g/cc 1.8 Appearance LightPink Flammability, UL94 V-0 Reinforcement Carrier Fiberglass Young s Modulus ,ASTM D575 kPa 110 (psi) (16) Thickness ,ASTM D374 0.508 to 6.35mm InherentSurface Tack 2 (1 side ) Electrical Properties Application Thermal management, Dielectric Breakdown Voltage ,ASTM D149,VAC >6,000 TIM(Thermal Interface Material) Dielectric Constant ,ASTM D150 ,1,000Hz 5.0 Operating Temperature -60 to 200C 11 Volume Resistivity ,ASTM D257 ,ohm-meter 110 Range Thermal Properties Thermal Conductivity ,ASTM D5470 ,W/(m-K) 1.3 FEATURES AND BENEFITS Thermal Conductivity: 1.3W/m-K Thermal Impedance vs. Strain 2 (1) Highly Conformable, low hardness Thermal Impedance ,C-in /W ,0.040 : Decreased strainon fragilecomponents 10% Deflection 1.69 Fiberglass reinforced for puncture, shear and tear 20% Deflection 1.41 resistance 30% Deflection 1.26 Quick rebound to originalshape BERGQUIST GAP PAD TGP 1300 is a highly compliant Gap (1) The ASTM D5470 test fixture was utilized. The recorded values include the interfacial thermal resistance. The values are provided for reference only. Actual application Pad material that is ideal for fragile component leads . The performance is directly related to the surface roughness, flatness and pressure applied material is fiberglass reinforced for improved puncture resistance and handlingcharacteristics . GENERAL INFORMATION BERGQUIST GAP PAD TGP 1300 maintainsa conformable For safe handling information on this product, consult the yet elastic nature that allows for excellent interfacingand Safety Data Sheet, (SDS). wet-out characteristics, even to surfaces with highroughness and/or topography .BERGQUIST GAP PAD TGP 1300 features an inherent tack on both sides of the material, eliminatingthe Not for product specifications need for thermally impeding adhesive layers . The technical data contained herein are intended as reference only. Please contact your local quality department for assistance and recommendations on specifications for this product. TYPICAL APPLICATIONS Any heat-generating component and a heat sink CONFIGURATIONS AVAILABLE Computer and peripherals BERGQUIST GAP PAD TGP 1300 is available in the Telecommunications following configurations: Between any heat- generating semiconductor and a heat sink Sheet form and die-cut parts Shieldingdevices TYPICAL PROPERTIES OF CURED MATERIAL Young s modulus is calculated using 0.01in/min,step rate of strainwith a sample size 0.79inch.TDS BERGQUIST GAP PAD TGP 1300, November -2018 merchantability or fitness for a particular purpose, arising from sale or use STORAGE of Henkel Corporations products. Henkel Corporation specifically Store product in the unopened container in a dry location. disclaims any liability for consequential or incidental damages of any kind, Storage informationmay be indicated on the product container including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from labeling. domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We Optimal Storage: 25 C (3), 50 % RH (10) for a 12 months recommend that each prospective user test his proposed application before shelf life. Material removed from containers may be repetitive use, usingthisdata as a guide.Thisproduct may be covered by one or contaminated during use. Do not return product to the original more United States or foreign patents or patent applications. container. Henkel Corporation cannot assume responsibility for Trademark usage: Except as otherwise noted Alltrademarks inthisdocument are trademarks and/or registered trademarks of Henkel and its affiliatesinthe product which has been contaminated or stored under U.S.and elsewhere. conditions other thanthose previously indicated.Ifadditional information is required, please contact your local Technical Service Center or Customer Service Representative. Reference 1 Conversions (C x 1.8)+ 32 = F kV/mm x 25.4 = V/mil mm /25.4 = inches Nx 0.225 = lb N/mm x 5.71 = lb/in psi x 145 = N/mm MPa = N/mm Nm x 8.851 = lbin Nm x 0.738= lbft Nmm x 0.142= ozin mPas = cP Disclaimer Note: The information provided in this Technical Data Sheet (TDS) includingthe recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of thisTDS.The product can have a variety of different applications as well as differingapplication and working conditions inyour environment thatare beyond our control. Henkel is, therefore, not liablefor the suitabilityof our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trialsto confirm such suitabilityof our product. Any liabilityinrespect of the informationinthe Technical DataSheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except inrelation to death or personal injury caused by our negligence and any liabilityunder any applicable mandatory product liabilitylaw. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: Incase Henkel would be nevertheless held liable,on whatever legal ground, Henkels liabilitywill inno event exceed the amount of the concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) includingthe recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of thisTDS. Henkel is, therefore, not liablefor the suitabilityof our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trialsto confirm such suitabilityof our product. Any liabilityinrespect of the informationinthe Technical DataSheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except inrelation to death or personal injury caused by our negligence and any liabilityunder any applicable mandatory product liabilitylaw. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnishedfor informationonly and are believed to be reliable. We cannot assume responsibility for the results obtained by others over whose methods we have no control. Itis the user s responsibility to determine suitabilityfor the user s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons againstany hazards thatmay be involved inthe handling and use thereof. Inlightof the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.3898.4800 For the most direct access to local sales and technical support visit: www.henkel.com/electronics