TechnicalData Sheet BERGQUIST GAP PAD TGP 3000 Known as BERGQUIST GAP PAD 3000S30 April-2021 PRODUCT DESCRIPTION TYPICAL APPLICATIONS Thermally Conductive, Reinforced,Soft S-ClassGap Filling Processors Material. Server S-RAMs Massstorage drives Technology Silicone Wireline/wirelesscommunications hardware Appearance Lightblue Notebook computers Reinforcement CarrierFiberglass BGA packages Thickness 0.254 to 3.175mm Power conversion ,ASTM D374 Inherent Surface Tack 2 (2 sides) TYPICAL PROPERTIES OF CURED MATERIAL Application Thermal management, Young s modulus iscalculatedusing 0.01in/min,step rate TIM(Thermal InterfaceMaterial) ofstrain with a sample size0.79inch. Operating Temperature -60 to 200C Physical Properties Range Hardness, Shore 00,Thirty second delay value , 30 ASTM D2240 ,Bulk rubber Heat Capacity ,ASTM E1269,J/g-K 1.0 FEATURES AND BENEFITS Density ,ASTM D792,g/cc 3.2 Thermal Conductivity: 3.0W/m-K Flammability, UL 94 V-0 Low S-Classthermal resistanceat very low pressures Young s modulus ,ASTM D575 KPa 180 Highlyconformable,S-Classsoftness (psi) (26) Designedforlow-stressapplications Fiberglassreinforcedfor puncture, shear and tear resistance Electrical Properties DielectricBreakdown Voltage ,ASTM D149,VAC >3,000 BERGQUIST GAP PAD TGP 3000 isa soft gap filling DielectricConstant ,ASTM D150,1,000Hz 7.0 material rated at a thermal conductivity of 3 W/m-K . The 9 Volume Resistivity,ASTM D257,ohm-meter 110 material offersexceptional thermal performance at low pressures due to an allnew 3 W/m-K fillerpackage and Thermal Properties low-modulus resinformulation . It isreinforcedto enhance Thermal Conductivity ,ASTM D5470 ,W/(m-K) 3.0 material handling,puncture, shear and tear resistance.It is Note:Resultant thicknessisdefinedas the finalgap wellsuited forhighperformance, low-stressapplicationsthat typically use fixedstandoff or clipmounting . BERGQUIST thicknessofthe application. GAP PAD TGP 3000 maintains a conformable yet elastic nature that allows for excellent interfacingand wet-out Thickness vs. Thermal Resistance characteristics,even to surfaces with highroughness and/or BERGQUIST GAP PAD TGP 3000 topography . 130 BERGQUIST GAP PAD TGP 3000 isofferedwith natural 110 inherent tack on both sidesof the material,eliminatingthe need forthermally-impeding adhesivelayers.The materials 90 natural inherent tack allowsforstick-in-placecharacteristics during assembly . BERGQUIST GAP PAD TGP 3000 is 70 supplied with protective linerson both sides. The top side has reduced tack foreaseofhandling. 50 30 10 0.10 0.30 0.50 0.70 0.90 1.10 1.30 1.50 1.70 Thermal Resistance C-in/W Resultant Thickness (mils)TDS BERGQUIST GAP PAD TGP 3000, April-2021 GENERAL INFORMATION Disclaimer The information provided in this TechnicalData Sheet (TDS) includingthe For safe handling information on this product, consult recommendations for use and application of the product are based on our the Safety Data Sheet, (SDS). knowledge and experience of the product as at the date of this TDS. The product can have a variety of differentapplications as well as differing applicationand working conditionsinyour environment that are beyond our Not for product specifications control.Henkelis,therefore,not liableforthe suitability ofour product forthe The technical data contained herein are intended as production processesand conditionsinrespect ofwhich you use them, as well referenceonly. Pleasecontact your localquality department as the intended applicationsand results. We strongly recommend that you carry out your own prior trialsto confirm such suitability of our product. Any for assistanceand recommendations on specificationsfor liabilityinrespect ofthe information inthe TechnicalData Sheet or any other thisproduct. written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitlyagreed and except inrelationto death or personal injury caused by our negligenceand any liabilityunder any CONFIGURATIONS AVAILABLE applicablemandatory product liabilitylaw. BERGQUIST GAP PAD TGP 3000 isavailablein the In case products are delivered by Henkel Belgium NV,Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS followingconfigurations: and Henkel France SA please additionally note the following: In caseHenkelwould be neverthelessheldliable,on whatever legalground, Sheet form Henkelsliabilitywillinno event exceed the amount ofthe concerned delivery. Die-Cutparts In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: Natural tack both sideswith fiberglass. The information provided in this TechnicalData Sheet (TDS) includingthe recommendations for use and application of the product are based on our knowledge and experience ofthe product as at the date ofthisTDS. Henkel is,therefore,not liablefor the suitability of our product for the production STORAGE processesand conditionsinrespect of which you use them, as wellas the Store product inthe unopened container ina dry location. intended applicationsand results.We strongly recommend that you carry out your own priortrialsto confirmsuch suitabilityofour product. Storage information may be indicated on the product Any liabilityinrespect ofthe information inthe TechnicalData Sheet or any container labeling. other written or oralrecommendation(s) regarding the concerned product is excluded, except ifotherwise explicitlyagreed and except inrelationto death Optimal Storage: 25C (3), 50% RH (10) fora 12 months or personal injury caused by our negligenceand any liabilityunder any applicablemandatory product liabilitylaw. shelflife.Materialremoved from containers may be In case products are delivered by Henkel Corporation, or Henkel Canada contaminated during use. Do not return product to the Corporation, the following disclaimer is applicable: originalcontainer. Henkel Corporation cannot assume The data contained hereinare furnished forinformation only and are believed responsibilityfor product which has been contaminated or to be reliable.We cannot assume responsibilityfor the results obtained by stored under conditions other than those previously others over whose methods we have no control.It isthe user s responsibility to determine suitability for the user s purpose of any production methods indicated.Ifadditionalinformation isrequired,pleasecontact mentioned hereinand to adopt such precautions as may be advisableforthe your localTechnicalService Center or Customer Service protection of property and of persons against any hazards that may be Representative. involved in the handlingand use thereof.In lightof the foregoing,Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Conversions Henkel Corporation specifically disclaims any liability for consequential (C x 1.8)+ 32 =F or incidental damages of any kind, including lost profits. The discussion kV/mm x 25.4 =V/mil hereinof various processes or compositions isnot to be interpreted as representation that they are freefrom domination ofpatents owned by others mm /25.4 =inches or as a licenseunder any HenkelCorporation patents that may cover such N x 0.225=lb/F processesor compositions.We recommend that each prospective user test N/mm x 5.71=lb/in hisproposed applicationbeforerepetitive use, using thisdata as a guide.This product may be covered by one or more United States or foreignpatents or psi x 145 =N/mm patent applications. MPa =N/mm Trademark usage Nm x 8.851 = lbin Except as otherwise noted, alltrademarks inthisdocument are trademarks of Nm x 0.738=lbft HenkelCorporation in the U.S. and elsewhere. denotes a trademark registeredinthe U.S.Patent and Trademark Office. Nmm x 0.142 =ozin mPas =cP Reference2 For the most direct access to local sales and technical support visit: