Technical Data Sheet BERGQUIST GAP PAD TGP HC3000 Known as BERGQUIST GAP PAD HC 3.0 November -2018 PRODUCT DESCRIPTION TYPICAL PROPERTIES OF CURED MATERIAL High-Compliance, Thermally Conductive, Low Modulus Physical Properties Material . Hardness, Shore 00,Thirty second delay value , 15 ASTM D2240,Bulk rubber Technology Silicone Heat Capacity ,ASTM E1269,J/g-K 1.0 Appearance Blue Density ,Bulk rubber ,ASTM D792,g/cc 3.1 Reinforcement Carrier Fiberglass Flammability, UL 94 V-0 (1) Thickness 0.508 to 3.175 mm Young s Modulus ,ASTM D575 kPa 110 (psi) (16) ASTM D374 Inherent Surface Tack 2 Application Thermal management, Electrical Properties TIM(Thermal Interface Material) Dielectric Breakdown Voltage ,ASTM D149, 5,000 Operating Temperature -60 to 200C Minimum value 20 mil,VAC Range Dielectric Constant ,ASTM D150 ,1,000Hz 6.5 10 Volume Resistivity ,ASTM D257,ohm-meter 110 FEATURES AND BENEFITS Thermal Properties Thermal Conductivity: 3.0W/m-K Thermal Conductivity ,ASTM D5470,W/(m-K) 3.0 (2) High-compliance,low compression stress Thermal Impedance ,0.040 2 ASTM D5470,C-in /W : Fiberglassreinforced for shear and tear resistance 10% Deflection 0.57 20% Deflection 0.49 BERGQUIST GAP PAD TGP HC3000 isa soft and compliant gap fillingmaterial with a thermal conductivity of 3.0 W/m-K . 30% Deflection 0.44 The material offers exceptional thermal performance at low pressures due to a unique 3.0 W/m-K fillerpackage and (1) Youngs Modulus, calculated using 0.01in/min.step rate of strain with a sample size of low-modulus resin formulation .The enhanced material isideal 0.79inch2after 5 minutes of compression at 10% strain on a 1mm thickness material for applications requiring low stress on components and boards (2) The ASTM D5470 test fixture was utilized. The recorded values include the interfacial thermal resistance. The values are provided for reference only. Actual application during assembly . performance isdirectly related to the surface roughness, flatnessand pressure applied BERGQUIST GAP PAD TGP HC3000 maintains a conformable nature that allows for quick recovery and excellent GENERAL INFORMATION wet-out characteristics, even to surfaces with highroughness For safe handling information on this product, consult the and/or topography . BERGQUIST GAP PAD TGP HC3000 is Safety Data Sheet, (SDS). offered with natural inherent tack on both sides of the material, eliminating the need for thermally- impeding adhesive layers . The top side has minimal tack for ease of handling. Not for product specifications BERGQUIST GAP PAD TGP HC3000 is supplied with The technical data contained herein are intended as reference protective linerson both sides. only. Please contact your local quality department for assistance and recommendations on specifications for this product. TYPICAL APPLICATIONS CONFIGURATIONS AVAILABLE Telecommunications BERGQUIST GAP PAD TGP HC3000 isavailable inthe ASICs and DSPs following configurations: Consumer electronics Thermal modules to heat sinks Sheet form and die-cut partsTDS BERGQUIST GAP PAD TGP HC3000, November -2018 merchantability or fitness for a particular purpose, arising from sale or use STORAGE of Henkel Corporations products. Henkel Corporation specifically Store product in the unopened container in a dry location. disclaims any liability for consequential or incidental damages of any kind, Storage information may be indicated on the product container including lost profits. The discussion herein of various processes or compositions isnot to be interpreted as representation that they are free from labeling. domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We Optimal Storage: 25 C (3), 50 % RH (10) for a 12 months recommend that each prospective user test hisproposed application before shelf life. Material removed from containers may be repetitive use, using thisdata as a guide. Thisproduct may be covered by one or contaminated during use. Do not return product to the original more United States or foreign patents or patent applications. container. Henkel Corporation cannot assume responsibility for Trademark usage: Except as otherwise noted Alltrademarks inthisdocument are trademarks and/or registered trademarks of Henkel and its affiliatesinthe product which has been contaminated or stored under U.S.and elsewhere. conditions other than those previously indicated. Ifadditional information is required, please contact your local Technical Service Center or Customer Service Representative. Reference 1 Conversions (C x 1.8)+ 32 = F kV/mm x 25.4 = V/mil mm /25.4 = inches Nx 0.225 = lb N/mm x 5.71= lb/in psi x 145 = N/mm MPa = N/mm Nm x 8.851 = lbin Nm x 0.738= lbft Nmm x 0.142= ozin mPas = cP Disclaimer Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of thisTDS.The product can have a variety of different applications as well as differingapplication and working conditions inyour environment that are beyond our control. Henkel is, therefore, not liablefor the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trialsto confirm such suitability of our product. Any liabilityinrespect of the information inthe Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product isexcluded, except ifotherwise explicitly agreed and except inrelation to death or personal injury caused by our negligence and any liabilityunder any applicable mandatory product liabilitylaw. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: Incase Henkel would be nevertheless held liable,on whatever legal ground, Henkels liabilitywill inno event exceed the amount of the concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of thisTDS. Henkel is, therefore, not liablefor the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trialsto confirm such suitability of our product. Any liabilityinrespect of the information inthe Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product isexcluded, except ifotherwise explicitly agreed and except inrelation to death or personal injury caused by our negligence and any liabilityunder any applicable mandatory product liabilitylaw. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnished for information only and are believed to be reliable. We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons againstany hazards that may be involved inthe handling and use thereof. Inlight of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.3898.4800 For the most direct access to local sales and technical support visit: www.henkel.com/electronics