TechnicalDataSheet BERGQUIST GAP PAD TGP HC5000 Known as BERGQUIST GAP PAD HC 5.0 November -2018 PRODUCT DESCRIPTION TYPICAL PROPERTIES OF CURED MATERIAL Highly Conformable, Thermally Conductive, Low Modulus Physical Properties Material. Hardness, Shore00,Thirtysecond delay value , 35 ASTM D2240 ,Bulk rubber Technology Silicone HeatCapacity,ASTM E1269,J/g-K 1.0 Appearance Violet Density ,Bulk rubber,ASTM D792,g/cc 3.2 ReinforcementCarrierFiberglass Flammability, UL94 V-0 (1) Thickness *0.508,1.016,1.524, Young s Modulus ,ASTM D575 kPa 121 2.032,2.540,3.175 (psi) (17.5) ASTM D374 InherentSurface Tack 2 Application Thermal management, Electrical Properties TIM(Thermal InterfaceMaterial) DielectricBreakdown Voltage ,ASTM D149, 5,000 OperatingTemperature -60 to200C Minimum value 20 mil,VAC Range DielectricConstant,ASTM D150 ,1,000Hz 8.0 10 Volume Resistivity,ASTM D257,ohm-meter 110 *Custom thicknesses available.Please contactyour Henkel Thermal Properties Sales Representative formore information. Thermal Conductivity,ASTM D5470,W/(m-K) 5.0 (2) Thermal Impedance ,0.040 FEATURES AND BENEFITS 2 ASTM D5470,C-in/W: Thermal Conductivity:5.0W/m-K 10% Deflection 0.35 High-compliance,low compression stress 20% Deflection 0.3 Fiberglassreinforcedforshear and tearresistance 30% Deflection 0.26 BERGQUIST GAP PAD TGP HC5000 is a soft and compliant gap fillingmaterialwith a thermalconductivity of 5.0 W/m-K . (1) Youngs Modulus, calculated using 0.01in/min.step rateof strainwith a sample size of 0.79inch2after5 minutes of compression at10% strainon a 1mm thicknessmaterial The materialoffers exceptionalthermal performance at low (2) The ASTM D5470 testfixture was utilized.The recorded values include the interfacial pressures due toa unique fillerpackage and low-modulus resin thermal resistance.The values are provided for reference only. Actual application performance isdirectlyrelatedtothesurface roughness, flatness and pressure applied formulation. The enhanced materialis idealfor applications requiringlow stress on components and boards during assembly . GENERAL INFORMATION BERGQUIST GAP PAD TGP HC5000 maintains a For safe handling information on this product, consult the conformable nature that allows excellent interfacingand Safety Data Sheet, (SDS). wet-out characteristics,even tosurfaces with highroughness and/ortopography . BERGQUIST GAP PAD TGP HC5000 is Not for product specifications offered with naturalinherenttackon bothsides of thematerial, The technicaldata containedhereinare intendedas reference eliminatingthe need forthermally-impeding adhesive layers . only. Please contactyour local quality department for The top side has minimal tack for ease of handling. assistance and recommendations on specificationsfor this BERGQUIST GAP PAD TGP HC5000 is supplied with product. protectivelinerson bothsides . CONFIGURATIONS AVAILABLE BERGQUIST GAP PAD TGP HC5000 is availableinthe TYPICAL APPLICATIONS followingconfigurations: Telecommunications Sheet form and die-cutparts ASICs and DSPs Consumer electronics Thermal modules toheatsinksTDS BERGQUIST GAP PAD TGP HC5000, November -2018 merchantability or fitness for a particular purpose, arising from sale or use STORAGE of Henkel Corporations products. Henkel Corporation specifically Storeproduct inthe unopened containerina dry location. disclaims any liability for consequential or incidental damages of any kind, Storageinformationmay be indicatedon theproduct container including lost profits. The discussion herein of various processes or compositionsis nottobe interpretedas representationthatthey are free from labeling. dominationof patents owned by others or as a license under any Henkel Corporationpatents thatmay cover such processes or compositions.We OptimalStorage:25C (3), 50% RH (10) for a 12 months recommend thateach prospective user test his proposed applicationbefore shelf life.Materialremoved from containers may be repetitiveuse, using thisdata as a guide. This product may be covered by one or contaminatedduring use. Do notreturnproduct tothe original more UnitedStatesorforeignpatents orpatentapplications. container.Henkel Corporationcannotassume responsibilityfor Trademark usage: Except as otherwise noted Alltrademarks inthisdocument are trademarks and/orregisteredtrademarks of Henkel and itsaffiliatesinthe product which has been contaminated or stored under U.S.and elsewhere. conditionsotherthan those previously indicated.Ifadditional informationis required, please contactyour localTechnical Service CenterorCustomer Service Representative. Reference 1 Conversions (C x 1.8)+ 32 = F kV/mm x 25.4= V/mil mm /25.4= inches N x 0.225= lb N/mm x 5.71= lb/in psi x 145 = N/mm MPa = N/mm Nm x 8.851 = lbin Nm x 0.738= lbft Nmm x 0.142= ozin mPas = cP Disclaimer Note: The informationprovided inthisTechnicalData Sheet (TDS) includingthe recommendations for use and applicationof the product are based on our knowledge and experience of theproduct as atthedate of thisTDS. The product can have a variety of differentapplicationsas well as differingapplicationand working conditionsinyour environment thatare beyond our control.Henkel is, therefore,notliableforthesuitabilityof our product fortheproductionprocesses and conditionsinrespect of which you use them, as well as the intended applicationsand results. We strongly recommend thatyou carry out your own priortrialstoconfirmsuch suitabilityof our product. Any liabilityinrespect of theinformationintheTechnicalDataSheet orany other writtenororalrecommendation(s) regardingthe concerned product isexcluded, except ifotherwise explicitlyagreed and except inrelationtodeath orpersonal injury caused by our negligenceand any liabilityunder any applicablemandatory product liabilitylaw. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: Incase Henkel would be nevertheless held liable,on whatever legalground, Henkels liabilitywillinno event exceed theamount of theconcerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The informationprovided inthisTechnicalData Sheet (TDS) includingthe recommendations for use and applicationof the product are based on our knowledge and experience of the product as atthe date of thisTDS. Henkel is, therefore,notliableforthesuitabilityof our product fortheproductionprocesses and conditionsinrespect of which you use them, as well as the intended applicationsand results. We strongly recommend thatyou carry out your own priortrialstoconfirmsuch suitabilityof our product. Any liabilityinrespect of theinformationintheTechnicalDataSheet orany other writtenororalrecommendation(s) regardingthe concerned product isexcluded, except ifotherwise explicitlyagreed and except inrelationtodeath orpersonal injury caused by our negligenceand any liabilityunder any applicablemandatory product liabilitylaw. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data containedhereinarefurnished forinformationonly and are believed to be reliable.We cannotassume responsibilityforthe results obtainedby others over whose methods we have no control.Itis the user s responsibilityto determinesuitabilityfortheuser s purpose of any productionmethods mentioned hereinand toadopt such precautions as may be advisable forthe protectionof property and of persons againstany hazards thatmay be involved inthehandling and use thereof.Inlightof the foregoing,Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.3898.4800 For the most direct access to local sales and technical support visit: www.henkel.com/electronics