Technical Data Sheet BERGQUIST HIFLOW THF 3000UT Known as BERGQUIST HI-FLOW 565UT April -2020 Thermal Properties PRODUCT DESCRIPTION (1) Tacky, High Performance, Un-Reinforced Phase Change TIM . Thermal Conductivity ,ASTM D5470,W/(m-K) 3.0 Technology Phase Change Thermal Performance vs. Pressure TO-220 Thermal Performance ,C/W : Appearance Blue 10 psi 0.37 Reinforcement Carrier None 25psi 0.35 Total Thickness 0.127 to 0.254mm ,ASTM D374 50psi 0.34 100 psi 0.3 Application Thermal management, Thermally conductive adhesive 200 psi 0.26 2 (2) Operating Temperature 125C Thermal Impedance ,ASTM D5470,C-in /W : 10 psi 0.09 FEATURES AND BENEFITS 25psi 0.05 2 50psi 0.03 Thermal impedance: 0.05C-in /W 25 psi High Thermal Conductivity: 3.0 W/m-K 100 psi 0.02 Phase change softening temp 52C 200 psi 0.02 Naturally tacky Tabulated for ease of assembly 1) This is the measured thermal conductivity of the Hi-Flow coating. It represents one conducting layer in a three- layer laminate. The Hi-Flow coatings are phase change TYPICAL APPLICATIONS compounds. These layers will respond to heat and pressure induced stresses. The overall conductivity of the material in post-phase change, thin filmproducts is highly dependent upon Processor lid to heat sink the heat and pressure applied. This characteristic is not accounted for in ASTM D5470. Please contact Bergquist Product Management ifadditional specifications are required. FBDIMM to heat spreader 2)The ASTM D5470test fixture was used and the test sample was conditioned at 70C prior Processor die to lid or heat sink to test. The recorded value includes interfacial thermal resistance. These values are provided for reference only. Actual application performance is directly related to the surface roughness, flatness and pressure applied. BERGQUIST HI FLOW THF 3000UT is a naturally tacky, thermally conductive phase change material which is supplied in an easy to use tabulated pad form . In the application the GENERAL INFORMATION material undergoes a phase change softening, starting near For safe handling information on this product, consult the Safety 52C. Data Sheet, (SDS). The phase change softening feature improves handling Not for product specifications characteristics prior to a facilitated assembly . At application The technical data contained herein are intended as reference temperatures and pressures, BERGQUIST HI FLOW THF only. Please contact your local quality department for 3000UT wets out the thermal interfaces producing a very low assistance and recommendations on specifications for this thermal impedance . product. The thermal performance of BERGQUIST HI FLOW THF CONFIGURATIONS AVAILABLE 3000UT is comparable to the best thermal greases . BERGQUIST HIFLOW THF 3000UT is supplied in: BERGQUIST HI FLOW THF 3000UT is provided at a consistent thickness to ensure reliable performance . Tabulated in roll form, kiss-cut parts no holes BERGQUIST HIFLOW THF 3000UT can be applied in high BERGQUIST HI FLOW THF 3000UT is limited to a volumes to the target surface via low pressure from a roller or square or rectangular part design. Dimensional manual application. tolerance is +/-0.020inch (0.5mm) TYPICAL PROPERTIES Physical Properties Phase Change Temperature ,ASTM D3418 ,C 52 Flammability Rating, UL 94 V-0TDS BERGQUIST HIFLOW THF 3000UT , April -2020 Conversions (C x 1.8)+ 32 =F kV/mm x 25.4=V/mil mm /25.4=inches N x 0.225=lb/F N/mm x 5.71=lb/in psi x 145=N/mm MPa =N/mm Nm x 8.851 = lbin Nm x 0.738=lbft Nmm x 0.142=ozin mPas =cP Disclaimer Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. The product can have a variety of different applications as well as differing application and working conditions in your environment that are beyond our control. Henkel is, therefore, not liable for the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liability in respect of the information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except if otherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: In case Henkel would be nevertheless held liable,on whatever legal ground, Henkels liability will in no event exceed the amount of the concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. Henkel is, therefore, not liable for the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liability in respect of the information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnished for information only and are believed to be reliable. We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons against any hazards that may be involved in the handling and use thereof. In light of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications. Trademark usage Except as otherwise noted, all trademarks in this document are trademarks of Henkel Corporation in the U.S. and elsewhere. denotes a trademark registered in the U.S. Patent and Trademark Office. Reference 2 Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.2891.8000 For the most direct access to local sales and technical support visit: www.henkel.com/electronics