TechnicalData Sheet BERGQUIST LIQUI BOND TLB SA2000 BERGQUIST LIQUI-BOND SA 2000 January -2019 PRODUCT DESCRIPTION TYPICAL CURE SCHEDULE Thermally Conductive, One-Part, Liquid SiliconeAdhesive . Cure Schedule 20 minutes 125C or Technology Silicone 10 minutes 150C Appearance Yellow Time after cure temperature is achieved at the interface. Cure Heat cure Ramp time is application dependent. Application Thermal management, TIM(Thermal Interface Material) Operating Temperature -60 to 200C TYPICAL PROPERTIES OF CURED MATERIAL Range Physical Properties UL Flammability Rating UL 94 V-0 Hardness, Shore A,ASTM D2240 80 Electrical Properties FEATURES AND BENEFITS Dielectric Strength ,ASTM D149,V/mm 10,000 HighThermal Conductivity: 2.0W/m-K DielectricConstant ,ASTM D150,1,000Hz 6.0 Eliminates need for mechanical fasteners 11 Volume Resistivity ,ASTM D257,ohm-meter 110 One-part formulation for easy dispensing Mechanicaland chemicalstability Thermal Properties Maintains structural bond in severe environment Thermal Conductivity ,ASTM D5470 ,W/(m-K) 2.0 applications Heat cure TYPICAL PERFORMANCE OF CURED MATERIAL BERGQUIST LIQUI BOND TLB SA2000 is a high Shear Strength performance, thermally conductive siliconeadhesive that cures Shear Strength ,ASTM D1002 MPa 1.4 to a solid bonding elastomer .BERGQUIST LIQUIBOND TLB (psi) ( 200) SA2000 is supplied as a one-part liquid component, in either tube or mid-sized container form . GENERAL INFORMATION For safe handling information on this product, consult the Safety BERGQUIST LIQUIBOND TLB SA2000 features excellent low Data Sheet, (SDS). and high-temperature mechanical and chemical stability . The materials mild elastic properties assist in relieving CTE Not for product specifications stresses during thermal cycling. BERGQUIST LIQUIBOND The technicaldata contained herein are intended as reference TLB SA2000 cures at elevated temperatures and requires only. Please contact your localquality department for refrigeration storage at 10C . assistance and recommendations on specifications for this product. TYPICAL APPLICATIONS The above cure profiles are guideline recommendations. Cure PCBA to housing conditions (time and temperature) may vary based on customers experience and their application requirements, as Discrete component to heat spreader well as customer curing equipment, oven loadingand actual oven temperatures. TYPICAL PROPERTIES OF UNCURED MATERIAL Viscosity ,Brookfield -RV , -Helipath,ASTM D2196,25 C, CONFIGURATIONS AVAILABLE mPas (cP) : BERGQUIST LIQUIBOND TLB SA2000 is availablewith or Spindle TF,speed 20 rpm 200,000 without glass beads. Density ,ASTM D792,g/cc 2.4 ShelfLife 10C ,months 6 STORAGE Pot life 25C ,based on 1/8 diameter bead , 24 Store product in the unopened container in a dry location. hours Storage information may be indicated on the product container labeling.TDS BERGQUIST LIQUIBOND TLB SA2000 , January -2019 repetitive use, using this data as a guide. This product may be covered by one or Optimal Storage: 10C for a 6 month shelf life.Material more United States or foreignpatents or patent applications. removed from containers may be contaminated during use. Do Trademark usage: Except as otherwise noted Alltrademarks in this document not return product to the originalcontainer. Henkel Corporation are trademarks and/or registered trademarks of Henkel and its affiliatesin the cannot assume responsibility for product which has been U.S.and elsewhere. contaminated or stored under conditions other than those previously indicated. If additional information is required, Reference 2 please contact your localTechnical Service Center or Customer Service Representative. Conversions (C x 1.8)+ 32 =F kV/mm x 25.4 =V/mil mm /25.4 =inches N x 0.225=lb N/mm x 5.71=lb/in psi x 145 =N/mm MPa =N/mm Nm x 8.851 = lbin Nm x 0.738=lbft Nmm x 0.142 =ozin mPas =cP Disclaimer Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience ofthe product as at the date ofthis TDS. The product can have a variety of different applications as well as differingapplication and working conditions in your environment that are beyond our control. Henkel is, therefore, not liablefor the suitability ofour product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability ofour product. Any liabilityin respect ofthe information in the TechnicalData Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligenceand any liabilityunder any applicablemandatory product liabilitylaw. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: In case Henkel would be nevertheless held liable,on whatever legalground, Henkels liabilitywillin no event exceed the amount ofthe concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience ofthe product as at the date ofthis TDS. Henkel is, therefore, not liablefor the suitability ofour product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability ofour product. Any liabilityin respect ofthe information in the TechnicalData Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligenceand any liabilityunder any applicablemandatory product liabilitylaw. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnished for information only and are believed to be reliable.We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose ofany production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and ofpersons against any hazards that may be involved in the handling and use thereof. In lightof the foregoing,Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.3898.4800 For the most direct access to local sales and technical support visit: www.henkel.com/electronics