Technical Data Sheet BERGQUIST SILPAD TSP PP1200 Known as BERGQUIST POLY-PAD 1000 September -2019 PRODUCT DESCRIPTION Electrical Properties Polyester- Based, Thermally Conductive Insulation Material . Dielectric Breakdown Voltage ,ASTM D149,Vac 2,500 Dielectric Constant ,ASTM D150 1,000 Hz 4.5 Technology Polyester- based 11 Volume Resistivity ,ASTM D257,ohm-meter 110 Appearance Yellow Reinforcement Carrier Fiberglass Thermal Properties Total Thickness 0.229mm Thermal Conductivity ,ASTM D5470,W/(m-K) 1.2 ,ASTM D374 Thermal Performance vs. Pressure Application Thermal management, TO-220 Thermal Performance ,C/W Thermally conductive adhesive 10 psi 4.7 Operating Temperature -20 to 150C 25 psi 4.25 Range 50 psi 3.74 FEATURES AND BENEFITS 100 psi 3.27 2 Thermal impedance: 0.82C-in/W 50 psi 200 psi 2.89 Polyester based 2 (1) Thermal Impedance ,ASTM D5470,C-in/W For applications requiring non-silicone conformal coatings 10 psi 1.3 Designed for silicone- sensitive applications requiring high performance 25 psi 1.02 50 psi 0.82 TYPICAL APPLICATIONS 100 psi 0.61 Power supplies 200 psi 0.43 Automotive electronics Motor controls I)The ASTM D5470 test fixture was used. The recorded value includes interfacial thermal Power semiconductors resistance. These values are provided for reference only. Actual application performance is directly related to the surface roughness, flatness and pressure applied. BERGQUIST SILPAD TSP PP1200 is a fiberglass- reinforced insulator coated with a filledpolyester resin .The material offers superior thermal resistance for high performance applications . GENERAL INFORMATION For safe handling information on this product, consult the Safety Polyester- based, thermally conductive insulators from Data Sheet, (SDS). BERGQUIST provide a complete family of materials for Not for product specifications silicone- sensitive applications .Poly-Pads are ideally suited for The technical data contained herein are intended as reference applications requiring conformal coatings or applications where only. Please contact your local quality department for silicone contamination is a concern (telecomm and certain assistance and recommendations on specifications for this aerospace applications) . product. Poly-Pads are constructed with ceramic- filledpolyester resins CONFIGURATIONS AVAILABLE coating either side of a fiberglass carrier or a filmcarrier .The BERGQUIST SILPAD TSP PP1200 are supplied in: Poly-Pad family offers a complete range of performance Sheet form, roll form and die-cut parts characteristics to match individual applications . With or without pressure- sensitive adhesive TYPICAL PROPERTIES Physical Properties Hardness, Shore A,ASTM D2240 90 Breaking Strength ,ASTM D1458,KN/m 18 Elongation ,ASTM D412 ,% 10 Tensile Strength ,ASTM D412 ,MPa 48TDS BERGQUIST SILPAD TSP PP1200 , September -2019 Conversions (C x 1.8)+ 32 =F kV/mm x 25.4 =V/mil mm /25.4 =inches N x 0.225=lb/F N/mm x 5.71=lb/in psi x 145 =N/mm MPa =N/mm Nm x 8.851 = lbin Nm x 0.738=lbft Nmm x 0.142 =ozin mPas =cP Disclaimer Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS.The product can have a variety of differentapplications as well as differingapplication and working conditions inyour environment that are beyond our control. Henkel is, therefore, not liable for the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liability inrespect of the information inthe Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except inrelation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: Incase Henkel would be nevertheless held liable,on whatever legal ground, Henkels liability will inno event exceed the amount of the concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. Henkel is, therefore, not liable for the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liability inrespect of the information inthe Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except inrelation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnished for information only and are believed to be reliable. We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons against any hazards that may be involved inthe handling and use thereof. In light of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications. Trademark usage: Except as otherwise noted All trademarks inthis document are trademarks and/or registered trademarks of Henkel and its affiliates in the U.S. and elsewhere. Reference 2 Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.3898.4800 For the most direct access to local sales and technical support visit: www.henkel.com/electronics