TechnicalData Sheet BERGQUIST SILPAD TSP Q2000 Known as BERGQUIST Q-PAD 3 November -2018 PRODUCT DESCRIPTION Electrical Properties Glass- Reinforced Grease Replacement Thermal Interface . DielectricBreakdown Voltage ,ASTM D149,Vac Non-Ins ulating Technology Silicone DielectricConstant ,ASTM D150 1,000 Hz NA Appearance Black 2 Volume Resistivity ,ASTM D257,ohm-meter 110 Reinforcement Carrier Fiberglass Total Thickness 0.127mm Thermal Properties ,ASTM D374 Thermal Conductivity ,ASTM D5470,W/(m-K) 2.0 Application Thermal management, Thermal Performance vs. Pressure Thermally conductive adhesive TO-220 Thermal Performance ,C/W Operating Temperature -60 to 180C 10 psi 2.26 Range 25psi 1.99 FEATURES AND BENEFITS 50psi 1.76 2 Thermal impedance: 0.35C-in/W 50 psi 100 psi 1.53 Eliminates processing constraints typically associated 200 psi 1.3 with grease 2 (1) Thermal Impedance ,ASTM D5470,C-in/W Conforms to surface textures 10 psi 0.65 Easy handling 25psi 0.48 May be installed prior to soldering and cleaningwithout worry 50psi 0.35 100 psi 0.24 TYPICAL APPLICATIONS 200 psi 0.16 Between a transistor and a heat sink Between two large surfaces such as an L-bracket and the chassis of an assembly I)The ASTM D5470test fixture was used. The recorded value includes interfacialthermal resistance. These values are provided for reference only. Actual application performance is Between a heat sink and a chassis directly related to the surface roughness, flatness and pressure applied. Under electrically isolated power modules or devices such as resistors, transformers and solid state relays GENERAL INFORMATION BERGQUIST SIL PAD TSP Q2000 eliminates problems For safe handling information on this product, consult the Safety associated with thermal grease such as contamination of Data Sheet, (SDS). electronic assemblies and reflow solder baths . BERGQUIST Not for product specifications SIL PAD TSP Q2000 may be installed prior to soldering and The technical data contained herein are intendedas reference cleaningwithout worry . only. Please contact your local quality department for When clamped between two surfaces, the elastomer conforms assistance and recommendations on specifications for this to surface textures thereby creating an air-free interface product. between heat-generating components and heat sinks . CONFIGURATIONS AVAILABLE Fiberglass reinforcement enables BERGQUIST SIL PAD TSP Q2000 to withstand processing stresses without losing physical BERGQUIST SIL PAD TSP Q2000 are supplied in: integrity .Italso provides ease of handlingduring application . Sheet form, roll form and die-cut parts With or without pressure- sensitive adhesive TYPICAL PROPERTIES Physical Properties Hardness, Shore A,ASTM D2240 86 Flammability Rating, UL 94 V-0TDS BERGQUIST SIL PAD TSP Q2000 , November -2018 Conversions (C x 1.8)+ 32 =F kV/mm x 25.4=V/mil mm /25.4=inches N x 0.225=lb N/mm x 5.71=lb/in psi x 145=N/mm MPa =N/mm Nm x 8.851 = lbin Nm x 0.738=lbft Nmm x 0.142=ozin mPas =cP Disclaimer Note: The information provided inthis Technical Data Sheet (TDS) includingthe recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. The product can have a variety of differentapplications as well as differingapplication and working conditions inyour environment that are beyond our control. Henkel is, therefore, not liablefor the suitability of our product for the production processes and conditions inrespect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liabilityinrespect of the information inthe TechnicalData Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except inrelation to death or personal injury caused by our negligenceand any liabilityunder any applicable mandatory product liabilitylaw. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: Incase Henkel would be nevertheless held liable,on whatever legal ground, Henkels liabilitywillinno event exceed the amount of the concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided inthis Technical Data Sheet (TDS) includingthe recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. Henkel is, therefore, not liablefor the suitability of our product for the production processes and conditions inrespect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liabilityinrespect of the information inthe TechnicalData Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except inrelation to death or personal injury caused by our negligenceand any liabilityunder any applicable mandatory product liabilitylaw. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnished for information only and are believedto be reliable.We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons against any hazards that may be involved inthe handling and use thereof. Inlight of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide.This product may be covered by one or more UnitedStates or foreign patents or patent applications. Trademark usage: Except as otherwise noted Alltrademarks inthis document are trademarks and/or registered trademarks of Henkel and its affiliates inthe U.S. and elsewhere. Reference 1 Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.3898.4800 For the most direct access to local sales and technical support visit: www.henkel.com/electronics