Technical Data Sheet LOCTITE SI 100 January -2014 PRODUCT DESCRIPTION use. Do not return product to the original container. Henkel LOCTITE SI 100 provides the following product Corporation cannot assume responsibility for product which characteristics: has been contaminated or stored under conditions other than those previously indicated. Ifadditional information is required, Technology Silicone grease please contact your local Technical Service Center or Appearance gray Customer Service Representative. Application Thermal management Typical Assembly CPUs , GPUs , MCUs , ASICs , DC-DC Not for product specifications Applications converters ,IGBT and Transistors The technical data contained herein are intended as reference Operating Temperature -40 to 150 C only. Please contact your local quality department for assistance and recommendations on specifications for this LOCTITE SI 100 is recommended for high-temperature heat product. transfer in normal applications . It is used between heat generating devices and the surfaces to which they are Conversions mounted or other heat dissipating surfaces . This product (C x 1.8)+ 32 = F delivers excellent thermal resistance, offers high thermal kV/mm x 25.4 = V/mil conductivity and virtually no evaporation over a wide operating mm /25.4 = inches temperature range .It is nonflammable, oxidation resistant and N x 0.225 = lb does not promote rust or corrosion . N/mm x 5.71= lb/in N/mm x 145 = psi TYPICAL PROPERTIES MPa = N/mm Viscosity, Cone & Plate, mPas (cP) : MPa x 145 = psi -1 Temperature: 25 C, Shear Rate: 0.5 s 350,000 Nm x 8.851 = lbin Specific Gravity 25 C 1.94 Nm x 0.738= lbft Thermal Conductivity ,W/(m-K) 3.4 Nmm x 0.142= ozin Thermal Impedance ASTM-D-5470,C.in/W : mPas = cP 80psi 0.017 Disclaimer Note: The information provided in this Technical Data Sheet (TDS) GENERAL INFORMATION including the recommendations for use and application of the For safe handling information on this product, consult the product are based on our knowledge and experience of the Material Safety Data Sheet, (MSDS). product as at the date of this TDS. The product can have a variety of different applications as well as differing application DIRECTIONS FOR USE and working conditions in your environment that are beyond 1. For best results parts to be covered should be clean and our control. Henkel is, therefore, not liable for the suitability of free of oil and debris . our product for the production processes and conditions in 2. Apply appropriate material to substrate so that there is respect of which you use them, as well as the intended enough material to cover 100% of the surface between applications and results. We strongly recommend that you the component and the heat sink and the material leaves carry out your own prior trials to confirm such suitability of our a small fillet. product. 3. Place the heat sink on top of the component and secure Any liability in respect of the information in the Technical Data with clips, screws or other hardware . Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except if otherwise explicitly agreed and except in relation to death or personal Storage injury caused by our negligence and any liability under any Store product in the unopened container in a dry location. applicable mandatory product liability law. Storage information may be indicated on the product container labeling. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Optimal Storage: 5C to 30 C. Storage below 5C or Henkel Technologies France SAS and Henkel France SA greater than 30 C can adversely affect product properties. please additionally note the following: In case Henkel would be nevertheless heldliable, on whatever Material removed from containers may be contaminated during legal ground, Henkels liability will in no event exceed theTDS LOCTITE SI 100, January -2014 amount of the concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. Henkel is, therefore, not liable for the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liability in respect of the information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except if otherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada, Inc.the following disclaimer is applicable: The data contained herein are furnished for information only and are believed to be reliable. We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons against any hazards that may be involved in the handling and use thereof. In light of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications. Trademark usage Except as otherwise noted, all trademarks in this document are trademarks of Henkel Corporation in the U.S. and elsewhere. denotes a trademark registered in the U.S. Patent and Trademark Office. Reference 0.0 Henkel Americas Henkel Europe Henkel Asia Pacific +860.571.5100 +49.89.320800.1800 +86.21.2891.8859 For the most direct access to local sales and technical support visit: www.henkel.com/industrial