Technical Data Sheet BERGQUIST SILPAD TSP 1100ST Known as BERGQUIST SIL-PAD1100ST October -2018 PRODUCT DESCRIPTION TYPICAL PROPERTIES Affordable, Electrically Insulating, Thermally Conductive, Soft Physical Properties Tack Elastomeric Material . Hardness, Shore 00, 30 second delay , ASTM 85 D2240 Technology Silicone Hardness, Shore 00,ASTM D2240 (1) 85 Appearance Yellow Breaking Strength ,ASTM D1458,KN/m 0.5 Reinforcement Carrier Fiberglass Elongation ,45 to warp and fill,ASTM D412 ,% 16 Total Thickness 0.305mm Tensile Strength ,ASTM D412 ,MPa 1.5 Inherent Surface Tack 2 (2 sides ) Flammability Rating, UL 94 V-0 Application Thermal management, Thermally conductive adhesive Electrical Properties Operating Temperature -60 to 180C Dielectric Breakdown Voltage ,ASTM D149,Vac 5,000 Range Dielectric Constant ,ASTM D150 1,000 Hz 5.0 10 Volume Resistivity ,ASTM D257,ohm-meter 110 FEATURES AND BENEFITS Thermal Properties Inherent tack on both sides for exceptional thermal performance and easy placement Thermal Conductivity ,ASTM D5470,W/(m-K) 1.1 Re-positionable for higher utilization, ease of use and Thermal Performance vs. Pressure assembly error reduction TO-220 Thermal Performance ,C/W Lined on both sides for ease of handling prior to 10 psi 2.72 placement inhigh volume assemblies 25 psi 2.71 Exhibits exceptional thermal performance even at a low 50 psi 2.68 mounting pressure 100 psi 2.62 Fiberglass reinforced 200 psi 2.23 Value alternative to BERGQUIST SILPAD TSP 1800ST 2 (1) Thermal Impedance ,ASTM D5470,C-in/W TYPICAL APPLICATIONS 10 psi 0.75 Automotive ECMs 25 psi 0.71 Motor controls 50 psi 0.66 Power supplies 100 psi 0.61 Between an electronic power device and its heat sink 200 psi 0.57 BERGQUIST SILPAD TSP 1100ST is a fiberglass- reinforced thermal interface material featuring inherent tack on both sides . (1) The ASTM D5470 test fixture was utilized. The recorded values include the interfacial The material exhibits excellent thermal performance at low thermal resistance. The values are provided for reference only. Actual application mounting pressures . performance is directly related to the surface roughness, flatness and pressure applied BERGQUIST SILPAD TSP 1100ST is supplied on two liners for exceptionally easy handling prior to auto-placement in GENERAL INFORMATION high-volume assemblies .It is ideal for placement between an For safe handling information on this product, consult the Safety electronic power device and its heat sink. Data Sheet, (SDS). Not for product specifications The technical data contained herein are intended as reference only. Please contact your local quality department for assistance and recommendations on specifications for this product.TDS BERGQUIST SILPAD TSP 1100ST , October -2018 Trademark usage: Except as otherwise noted All trademarks inthis document CONFIGURATIONS AVAILABLE are trademarks and/or registered trademarks of Henkel and its affiliates in the BERGQUIST SILPAD TSP 1100ST is supplied in: U.S. and elsewhere. Sheet form, roll form and die-cut parts Reference 1 Top and bottom liners Conversions (C x 1.8)+ 32 =F kV/mm x 25.4 =V/mil mm /25.4 =inches N x 0.225=lb N/mm x 5.71=lb/in psi x 145 =N/mm MPa =N/mm Nm x 8.851 = lbin Nm x 0.738=lbft Nmm x 0.142 =ozin mPas =cP Disclaimer Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS.The product can have a variety of differentapplications as well as differingapplication and working conditions inyour environment that are beyond our control. Henkel is, therefore, not liable for the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liability inrespect of the information inthe Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except inrelation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: Incase Henkel would be nevertheless held liable,on whatever legal ground, Henkels liability will inno event exceed the amount of the concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. Henkel is, therefore, not liable for the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liability inrespect of the information inthe Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except inrelation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnished for information only and are believed to be reliable. We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons against any hazards that may be involved inthe handling and use thereof. In light of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications. Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.3898.4800 For the most direct access to local sales and technical support visit: www.henkel.com/electronics