Technical Data Sheet BERGQUIST SILPAD TSP 1200 Known as BERGQUIST SIL-PAD1000 November -2018 PRODUCT DESCRIPTION Thermal Properties HighPerformance Thermally Conductive Insulator . Thermal Resistance , Bergquist Flat Plate Test 0.35 2 Method ,C-in /W Technology Silicone Thermal Conductivity ,ASTM D5470,W/(m-K) 1.2 Appearance Pink Thermal Vacuum Weight Loss (TML),NASA 0.22 Reinforcement Carrier Fiberglass SP-R-0022A,% Total Thickness ,ASTM 0.23 0.025mm VolatileCondensable Material (VCM),NASA 0.08 D374 SP-R-0022A,% Application Thermal management, Thermally conductive adhesive Operating Temperature -60 to 180C GENERAL INFORMATION Range For safe handling information on this product, consult the Safety Data Sheet, (SDS). BERGQUIST SIL PAD TSP 1200 has the same excellent mechanical and physical characteristics ofour BERGQUIST Not for product specifications SILPAD TSP 900 while offeringa 35% reduction in thermal The technical data contained herein are intended as reference resistance . only. Please contact your local quality department for assistance and recommendations on specifications for this BERGQUIST SILPAD TSP 1200 is a composite ofsilicone product. rubber and fiberglass . It is boron nitride filledand offers low thermal resistance . CONFIGURATIONS AVAILABLE In addition, BERGQUIST SILPAD TSP 1200 is non-toxic and BERGQUIST SILPAD TSP 1200 is supplied in: resists damage from cleaning agents . The material is flame Tolerances retardant and is specially formulated for use as a thermally .015 inches are heldon width, length, holediameter and conductive insulator . holelocation. Contact the factory iftighter tolerances are required. TYPICAL PROPERTIES Physical Properties Sheet form Breaking Strength ,ASTM D1458 ,KN/m 18 6 x 6 ,6 x 12 ,8 x 8 ,10 x 10 ,or 12 x 12 Elongation ,45 to warp and fill,ASTM D412,% 40 Sheets are available from stock, with or without adhesive. Shore Hardness, ASTM D2240,Shore A 85 Rollform Specific Gravity ,ASTM D792 1.5 Sil-Padmaterials are available in rollform, with or without Tensile Strength ,ASTM D412, 45 to warp and fill, 30 adhesive. Contact the factory. MPa Special Shapes Electrical Properties We produce thousands ofspecials. Toolingcharges vary Dielectric Breakdown Voltage ,ASTM D149, 4,500 depending on tolerances and complexity ofthe part. minimum Dielectric Constant ,ASTM D150 1,000 Hz 4.5 Volume Resistivity ,ASTM D257,ohm-meter : 11 Normal 110 8 Moist 1.510TDS BERGQUIST SILPAD TSP 1200, November -2018 Conversions (C x 1.8)+ 32 = F kV/mm x 25.4 = V/mil mm /25.4 = inches N x 0.225 = lb N/mm x 5.71= lb/in psi x 145 = N/mm MPa = N/mm Nm x 8.851 = lbin Nm x 0.738= lbft Nmm x 0.142= ozin mPas = cP Disclaimer Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application ofthe product are based on our knowledge and experience ofthe product as at the date ofthis TDS. The product can have a variety ofdifferent applications as well as differingapplication and working conditions in your environment that are beyond our control. Henkel is, therefore, not liablefor the suitability ofour product for the production processes and conditions in respect ofwhich you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability ofour product. Any liabilityin respect ofthe information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liabilityunder any applicable mandatory product liabilitylaw. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: In case Henkel would be nevertheless held liable,on whatever legalground, Henkels liabilitywillin no event exceed the amount ofthe concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application ofthe product are based on our knowledge and experience ofthe product as at the date ofthis TDS. Henkel is, therefore, not liablefor the suitability ofour product for the production processes and conditions in respect ofwhich you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability ofour product. Any liabilityin respect ofthe information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liabilityunder any applicable mandatory product liabilitylaw. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnished for information only and are believed to be reliable.We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose ofany production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and ofpersons against any hazards that may be involved in the handling and use thereof. In light ofthe foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination ofpatents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications. Trademark usage: Except as otherwise noted Alltrademarks in this document are trademarks and/or registered trademarks of Henkel and its affiliatesin the U.S. and elsewhere. Reference 1 Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.3898.4800 For the most direct access to local sales and technical support visit: www.henkel.com/electronics