Technical Data Sheet BERGQUIST SILPAD TSP 1800ST Known as BERGQUIST SIL-PAD1500ST November -2018 PRODUCT DESCRIPTION Electrical Properties Electrically Insulating, Thermally Conductive, Soft Tack DielectricBreakdown Voltage ,ASTM D149,Vac 3,000 Elastomeric Material . DielectricConstant ,ASTM D150 1,000 Hz 6.1 11 Volume Resistivity ,ASTM D257,ohm-meter 110 Technology Silicone Appearance Blue Thermal Properties Reinforcement Carrier Fiberglass Thermal Conductivity ,ASTM D5470,W/(m-K) 1.8 Total Thickness 0.203mm Thermal Performance vs. Pressure ,ASTM D374 TO-220 Thermal Performance ,C/W Application Thermal management, 10 psi 1.54 Thermally conductive adhesive 25 psi 1.52 Operating Temperature -60 to 180C Range 50 psi 1.51 100 psi 1.49 FEATURES AND BENEFITS 200 psi 1.46 2 Thermal impedance: 0.23C-in /W 50 psi 2 (1) Naturally tacky on both sides Thermal Impedance ,ASTM D5470,C-in /W Pad is repositionable 10 psi 0.37 Excellent thermal performance 25 psi 0.28 Auto-placement and dispensable 50 psi 0.23 100 psi 0.21 TYPICAL APPLICATIONS 200 psi 0.2 Power supplies Automotive electronics I)The ASTM D5470 test fixture was used. The recorded value includes interfacial thermal Motor controls resistance. These values are provided for reference only. Actual application performance is directly related to the surface roughness, flatness and pressure applied. BERGQUIST SILPAD TSP 1800ST is a fiberglass reinforced thermal interface material that is naturally tacky on both sides . BERGQUIST SILPAD TSP 1800ST exhibits superior thermal GENERAL INFORMATION performance when compared to the competitors thermal For safe handling information on this product, consult the Safety interface materials . Data Sheet, (SDS). BERGQUIST SILPAD TSP 1800ST is supplied in sheet or roll Not for product specifications form for exceptional auto-dispensing and auto-placement in The technical data contained herein are intended as reference high volume assemblies .BERGQUIST SILPAD TSP 1800ST only. Please contact your local quality department for is intended for placement between an electronic power device assistance and recommendations on specifications for this and its heat sink . product. CONFIGURATIONS AVAILABLE TYPICAL PROPERTIES BERGQUIST SILPAD TSP 1800ST are supplied in: Physical Properties Sheet form, die-cut parts and slit-to- width roll form Shore Hardness, ASTM D2240 Shore 00 75 Breaking Strength ,ASTM D1458,KN/m 0.34 Elongation ,45 to warp and fill,ASTM D412 ,% 22 Tensile Strength ,ASTM D412 ,MPa 1.6 Flammability Rating, UL 94 V-0TDS BERGQUIST SILPAD TSP 1800ST , November -2018 Conversions (C x 1.8)+ 32 =F kV/mm x 25.4 =V/mil mm /25.4 =inches N x 0.225=lb N/mm x 5.71=lb/in psi x 145 =N/mm MPa =N/mm Nm x 8.851 = lbin Nm x 0.738=lbft Nmm x 0.142 =ozin mPas =cP Disclaimer Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience ofthe product as at the date ofthis TDS. The product can have a variety of different applications as well as differing application and working conditions in your environment that are beyond our control. Henkel is, therefore, not liablefor the suitability ofour product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability ofour product. Any liability in respect ofthe information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: In case Henkel would be nevertheless held liable,on whatever legal ground, Henkels liability will in no event exceed the amount ofthe concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience ofthe product as at the date ofthis TDS. Henkel is, therefore, not liablefor the suitability ofour product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability ofour product. Any liability in respect ofthe information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnished for information only and are believed to be reliable.We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose ofany production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and ofpersons against any hazards that may be involved in the handling and use thereof. In light of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications. Trademark usage: Except as otherwise noted Alltrademarks in this document are trademarks and/or registered trademarks of Henkel and its affiliates in the U.S.and elsewhere. Reference 1 Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.3898.4800 For the most direct access to local sales and technical support visit: www.henkel.com/electronics