Technical Data Sheet BERGQUIST SILPAD TSP 3500 Known as BERGQUIST SIL-PAD2000 November -2018 PRODUCT DESCRIPTION Thermal Performance vs. Pressure Higher Performance, High Reliability Insulator . TO-220 Thermal Performance 0.01 Technology Silicone 10 psi 2.61 Appearance White 25 psi 2.32 Reinforcement Carrier Fiberglass 50 psi 2.02 Total Thickness 0.254 to 0.508mm 100 psi 1.65 ,ASTM D374 200 psi 1.37 Application Thermal management, Thermally conductive adhesive Thermal Impedance Operating Temperature -60 to 200C 0.01 Range 10 psi 0.57 FEATURES AND BENEFITS 25 psi 0.43 2 Thermal impedance: 0.33C-in /W 50 psi 50 psi 0.33 Optimal heat transfer 100 psi 0.25 High Thermal Conductivity: 3.5W/m-K 200 psi 0.2 TYPICAL APPLICATIONS Power supplies I)The ASTM D5470 test fixture was used. The recorded value includes interfacial thermal Motor controls resistance. These values are provided for reference only. Actual application performance is directly related to the surface roughness, flatness and pressure applied. Power semiconductors Aerospace Avionics GENERAL INFORMATION For safe handling information on this product, consult the Safety BERGQUIST SILPAD TSP 3500 is a high performance, Data Sheet, (SDS). thermally conductive insulator designed for demanding aerospace and commercial applications . BERGQUIST SIL Not for product specifications PAD TSP 3500 is a silicone elastomer formulated to maximize The technical data contained herein are intended as reference the thermal and dielectricperformance ofthe filler/bindermatrix only. Please contact your local quality department for . assistance and recommendations on specifications for this product. The result is a grease- free,conformable material capable of meeting or exceeding the thermal and electrical requirements CONFIGURATIONS AVAILABLE ofhigh reliability electronic packaging applications . BERGQUIST SILPAD TSP 3500 are supplied in: Sheet form and die-cut parts TYPICAL PROPERTIES With or without pressure- sensitive adhesive Physical Properties Hardness, Shore A,ASTM D2240 90 Conversions (C x 1.8)+ 32 =F Flammability Rating, UL 94 V-0 kV/mm x 25.4 =V/mil Electrical Properties mm /25.4 =inches N x 0.225=lb/F DielectricBreakdown Voltage ,ASTM D149,Vac 4,000 N/mm x 5.71=lb/in DielectricConstant ,ASTM D150 1,000 Hz 4.0 11 psi x 145 =N/mm Volume Resistivity ,ASTM D257,ohm-meter 110 MPa =N/mm Thermal Properties Nm x 8.851 = lbin Nm x 0.738=lbft Thermal Conductivity ,ASTM D5470,W/(m-K) 3.5 Nmm x 0.142 =ozin mPas =cPTDS BERGQUIST SILPAD TSP 3500, November -2018 Disclaimer Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience ofthe product as at the date ofthis TDS. The product can have a variety of different applications as well as differing application and working conditions in your environment that are beyond our control. Henkel is, therefore, not liablefor the suitability ofour product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability ofour product. Any liability in respect ofthe information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: In case Henkel would be nevertheless held liable,on whatever legal ground, Henkels liability will in no event exceed the amount ofthe concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience ofthe product as at the date ofthis TDS. Henkel is, therefore, not liablefor the suitability ofour product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability ofour product. Any liability in respect ofthe information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnished for information only and are believed to be reliable.We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose ofany production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and ofpersons against any hazards that may be involved in the handling and use thereof. In light of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications. Trademark usage: Except as otherwise noted Alltrademarks in this document are trademarks and/or registered trademarks of Henkel and its affiliates in the U.S.and elsewhere. Reference 2 Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.2891.8000 For the most direct access to local sales and technical support visit: www.henkel.com/electronics