Technical Data Sheet BERGQUIST SILPAD TSP A2000 Known as BERGQUIST SIL-PADA1500 November -2018 PRODUCT DESCRIPTION Thermal Performance vs. Pressure Electrically Insulating, Thermally Conductive Elastomeric TO-220 Thermal Performance ,C/W Material . 10 psi 3.03 25 psi 2.62 Technology Silicone 50 psi 2.21 Appearance Green 100 psi 1.92 Reinforcement Carrier Fiberglass 200 psi 1.78 Total Thickness ,ASTM 0.254mm D374 2 (1) Thermal Impedance ,ASTM D5470,C-in /W Application Thermal management, 10 psi 0.59 Thermally conductive adhesive 25 psi 0.5 Operating Temperature -60 to 180C 50 psi 0.42 Range 100 psi 0.34 FEATURES AND BENEFITS 200 psi 0.31 2 Thermal impedance: 0.42C-in /W 50 psi Elastomeric compound coated on both sides I)The ASTM D5470 test fixture was used. The recorded value includes interfacial thermal resistance. These values are provided for reference only. Actual application performance is TYPICAL APPLICATIONS directly related to the surface roughness, flatness and pressure applied. Power supplies Automotive electronics GENERAL INFORMATION Motor controls For safe handling information on this product, consult the Safety Power semiconductors Data Sheet, (SDS). BERGQUIST SIL PAD TSP A2000 is a silicone-based, Not for product specifications thermally conductive and electrically insulating material . It The technical data contained herein are intended as reference consists ofa cured silicone elastomeric compound coated on only. Please contact your local quality department for both sides ofa fiberglass reinforcement layer . assistance and recommendations on specifications for this product. BERGQUIST SIL PAD TSP A2000 performs well under clamping pressure up to 200 psi and is an excellent choicefor CONFIGURATIONS AVAILABLE high performance applications requiring electricalisolation and BERGQUIST SILPAD TSP A2000 are supplied in: cut-through resistance . Sheet form, roll form and die-cut parts With or without pressure- sensitive adhesive TYPICAL PROPERTIES Physical Properties Conversions (C x 1.8)+ 32 =F Hardness, Shore A,ASTM D2240 80 kV/mm x 25.4 =V/mil Breaking Strength ,ASTM D1458,KN/m 12 mm /25.4 =inches Elongation ,45 to warp and fill,ASTM D412 ,% 40 N x 0.225=lb Flammability Rating, UL 94 V-0 N/mm x 5.71=lb/in psi x 145 =N/mm Electrical Properties MPa =N/mm DielectricBreakdown Voltage ,ASTM D149,Vac 6,000 Nm x 8.851 = lbin DielectricConstant ,ASTM D150 1,000 Hz 7.0 Nm x 0.738=lbft 11 Volume Resistivity ,ASTM D257,ohm-meter 110 Nmm x 0.142 =ozin mPas =cP Thermal Properties Thermal Conductivity ,ASTM D5470,W/(m-K) 2.0 Disclaimer Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on ourTDS BERGQUIST SILPAD TSP A2000, November -2018 knowledge and experience ofthe product as at the date ofthis TDS. The product can have a variety of different applications as well as differing application and working conditions in your environment that are beyond our control. Henkel is, therefore, not liablefor the suitability ofour product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability ofour product. Any liability in respect ofthe information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: In case Henkel would be nevertheless held liable,on whatever legal ground, Henkels liability will in no event exceed the amount ofthe concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience ofthe product as at the date ofthis TDS. Henkel is, therefore, not liablefor the suitability ofour product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability ofour product. Any liability in respect ofthe information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnished for information only and are believed to be reliable.We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose ofany production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and ofpersons against any hazards that may be involved in the handling and use thereof. In light of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications. Trademark usage: Except as otherwise noted Alltrademarks in this document are trademarks and/or registered trademarks of Henkel and its affiliates in the U.S.and elsewhere. Reference 1 Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.3898.4800 For the most direct access to local sales and technical support visit: www.henkel.com/electronics