Technical Data Sheet BERGQUIST SILPAD TSP A3000 Known as BERGQUIST SIL-PADA2000 November -2018 PRODUCT DESCRIPTION Thermal Properties Higher Performance, HighReliability Insulator . Thermal Conductivity ,ASTM D5470 ,W/(m-K) 3.0 Technology Silicone Thermal Performance vs. Pressure Appearance White TO-220 Thermal Performance ,C/W Reinforcement Carrier Fiberglass 0.015 Total Thickness 0.381 to 0.508mm 10 psi 2.05 ,ASTM D374 25 psi 1.94 Application Thermal management, 50 psi 1.86 Thermally conductive adhesive 100 psi 1.79 Operating Temperature -60 to 200C 200 psi 1.72 Range 2 (1) Thermal Impedance ,ASTM D5470 ,C-in/W FEATURES AND BENEFITS 2 0.015 Thermal impedance: 0.32C-in/W 50 psi 10 psi 0.53 Optimal heat transfer 25 psi 0.4 HighThermal Conductivity: 3.0W/m-K 50 psi 0.32 TYPICAL APPLICATIONS 100 psi 0.28 Motor drive controls 200 psi 0.26 Avionics High-voltage power supplies Power transistor /heat sink interface I)The ASTM D5470 test fixture was used. The recorded value includes interfacial thermal resistance. These values are provided for reference only. Actual application performance is directly related to the surface roughness, flatness and pressure applied. BERGQUIST SILPAD TSP A3000 is a conformable elastomer with very high thermal conductivity that acts as a thermal interface between electrical components and heat sinks . GENERAL INFORMATION BERGQUIST SILPAD TSP A3000 is for applications where For safe handling information on this product, consult the Safety optimal heat transfer is a requirement . Data Sheet, (SDS). This thermally conductive silicone elastomer is formulated to Not for product specifications maximize the thermal and dielectric performance of the The technical data contained herein are intended as reference filler/bindermatrix . The result is a grease- free, conformable only. Please contact your local quality department for material capable of meeting or exceeding the thermal and assistance and recommendations on specifications for this electrical requirements of high reliability electronic packaging product. applications . CONFIGURATIONS AVAILABLE TYPICAL PROPERTIES BERGQUIST SILPAD TSP A3000 are supplied in: Physical Properties Sheet form, roll form and die-cut parts Hardness, Shore A,ASTM D2240 90 With or without pressure- sensitive adhesive Heat Capacity ,ASTM E1269,J/g-K 1.0 Flammability Rating, UL 94 V-0 Electrical Properties Dielectric Breakdown Voltage ,ASTM D149,Vac 4,000 Dielectric Constant ,ASTM D150 1,000 Hz 7.0 11 Volume Resistivity ,ASTM D257,ohm-meter 110TDS BERGQUIST SILPAD TSP A3000, November -2018 Conversions (C x 1.8)+ 32 =F kV/mm x 25.4 =V/mil mm /25.4 =inches N x 0.225=lb N/mm x 5.71=lb/in psi x 145 =N/mm MPa =N/mm Nm x 8.851 = lbin Nm x 0.738=lbft Nmm x 0.142 =ozin mPas =cP Disclaimer Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. The product can have a variety of differentapplications as well as differingapplication and working conditions inyour environment that are beyond our control. Henkel is, therefore, not liable for the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liability inrespect of the information inthe Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except inrelation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and Henkel France SA please additionally note the following: Incase Henkel would be nevertheless held liable,on whatever legal ground, Henkels liability will inno event exceed the amount of the concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. Henkel is, therefore, not liable for the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liability inrespect of the information inthe Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except inrelation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnished for information only and are believed to be reliable. We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons against any hazards that may be involved inthe handling and use thereof. Inlight of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications. Trademark usage: Except as otherwise noted Alltrademarks inthis document are trademarks and/or registered trademarks of Henkel and its affiliates in the U.S. and elsewhere. Reference 1 Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.3898.4800 For the most direct access to local sales and technical support visit: www.henkel.com/electronics