Technical Data Sheet BERGQUIST SIL PAD TSP K1300 Known as BERGQUIST SIL-PADK-10 November -2018 PRODUCT DESCRIPTION GENERAL INFORMATION The HighPerformance Kapton Based Insulator . For safe handling information on this product, consult the Safety Data Sheet, (SDS). Technology Silicone Not for product specifications Appearance Beige The technical data contained herein are intended as reference Reinforcement Carrier Kapton only. Please contact your local quality department for Total Thickness 0.15 0.025 assistance and recommendations on specifications for this ,ASTM D374 mm product. Application Thermal management, CONFIGURATIONS AVAILABLE Thermally conductive adhesive Operating Temperature -60 to 180C BERGQUIST SILPAD TSP K1300 are supplied in: Range Special Thicknesses Available in a variety ofthicknesses to meet customer BERGQUIST SILPAD TSP K1300 is the high performance requirements. insulator developed in conjunction with DuPont .BERGQUIST SILPAD TSP K1300 combines special Kapton MT Polyimide Tolerances filmwith boron nitride filledsilicone rubber . The result is a .015 inches are heldon width, length, holediameter and product with good cut-through properties and excellent thermal holelocation. performance . Contact the factory iftighter tolerances are required. BERGQUIST SIL PAD TSP K1300 is designed to replace Sheet form ceramic insulators such as Beryllium Oxide, boron Nitride and 6 x 6 ,6 x 12 ,8 x 8 ,10 x 10 ,or 12 x 12 Alumina .These insulators are expensive and they break easily . Sheets are available from stock, with or without adhesive. BERGQUIST SILPAD TSP K1300 eliminates breakage and costs much less than ceramics . Rollform Sil-Padmaterials are available in rollform, with or without TYPICAL PROPERTIES adhesive. Contact the factory. Physical Properties Special Shapes Hardness, Shore A,ASTM D2240 90 We produce thousands ofspecials. Toolingcharges vary Breaking Strength ,ASTM D1458 ,KN/m 5 depending on tolerances and complexity ofthe part. Elongation ,45 to warp and fill,ASTM D412,% 40 Tensile Strength ,ASTM D412,MPa 35 Conversions Electrical Properties (C x 1.8)+ 32 = F Dielectric Breakdown Voltage ,ASTM D149 (VAC, 6,000 kV/mm x 25.4 = V/mil min) mm /25.4 = inches N x 0.225 = lb/F Dielectric Constant ,ASTM D150 1,000 Hz 3.7 12 N/mm x 5.71= lb/in Volume Resistivity ,ASTM D257,ohm-meter 110 psi x 145 = N/mm MPa = N/mm Thermal Properties Nm x 8.851 = lbin Thermal Conductivity ,ASTM D5470,W/(m-K) 1.3 Nm x 0.738= lbft Thermal Resistance Bergquist Flat Plate Test 0.2 2 Nmm x 0.142= ozin Method ,C-in /W mPas = cP Thermal Vacuum Weight Loss (TML),as 0.36 manufactured ,NASA SP-R-0022A,% VolatileCondensable Material (VCM),as 0.09 manufactured ,NASA SP-R-0022A,%TDS BERGQUIST SILPAD TSP K1300, November -2018 Disclaimer Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application ofthe product are based on our knowledge and experience ofthe product as at the date ofthis TDS. The product can have a variety ofdifferent applications as well as differingapplication and working conditions in your environment that are beyond our control. Henkel is, therefore, not liablefor the suitability ofour product for the production processes and conditions in respect ofwhich you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability ofour product. Any liabilityin respect ofthe information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liabilityunder any applicable mandatory product liabilitylaw. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV,Henkel Nederland BV,Henkel Technologies France SAS and Henkel France SA please additionally note the following: In case Henkel would be nevertheless held liable,on whatever legalground, Henkels liabilitywillin no event exceed the amount ofthe concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application ofthe product are based on our knowledge and experience ofthe product as at the date ofthis TDS. Henkel is, therefore, not liablefor the suitability ofour product for the production processes and conditions in respect ofwhich you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability ofour product. Any liabilityin respect ofthe information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liabilityunder any applicable mandatory product liabilitylaw. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnished for information only and are believed to be reliable.We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose ofany production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and ofpersons against any hazards that may be involved in the handling and use thereof. In light ofthe foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination ofpatents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications. Trademark usage: Except as otherwise noted Alltrademarks in this document are trademarks and/or registered trademarks of Henkel and its affiliatesin the U.S. and elsewhere. Reference 2 Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.2891.8000 For the most direct access to local sales and technical support visit: www.henkel.com/electronics