Technical Data Sheet BERGQUIST SIL PAD TSP T1200 Known as BERGQUIST SIL-PADTUBE 400 February -2020 PRODUCT DESCRIPTION GENERAL INFORMATION Silicone- Based, Thermally Conductive Tubes . For safe handling information on this product, consult the Safety Data Sheet, (SDS). Technology Silicone Not for product specifications Appearance Gray /Green The technical data contained herein are intended as reference Reinforcement Carrier Fiberglass only. Please contact your local quality department for Thickness /Wall , 0.305 assistance and recommendations on specifications for this ASTM D374 product. Application Thermal management, Thermally conductive adhesive STORAGE: Store product in the unopened container in a dry location. Operating Temperature -60 to 180C Range Storage information may be indicated on the product container labeling. FEATURES AND BENEFITS Thermal Conductivity: 0.9W/m-K Optimal Storage :8 to 28 C For clip-mounted plastic power packages Material removed from containers may be contaminated during TYPICAL APPLICATIONS use. Do not return product to the original container. Henkel Clip-mounted power semiconductors Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than TO-220, TO-218, TO-247 and TO-3P those previously indicated. Ifadditional information is required, BERGQUIST SIL PAD TSP T1200 provide thermally please contact your local Technical Service Center or conductive insulation for clip-mounted plastic power packages . Customer Service Representative. Sil-Pad Tubes are made of silicone rubber with high thermal CONFIGURATIONS AVAILABLE conductivity . BERGQUIST SILPAD TSP T1200 are supplied in: BERGQUIST SIL PAD TSP T1200 is ideal for applications TO-220, TO-218, TO-247 and TO-3P requiring average thermal conductivity and economy . BERGQUIST SILPAD TSP T1200 are designed to meet VDE, Conversions U.L. and TUV agency requirements . (C x 1.8)+ 32 =F kV/mm x 25.4=V/mil mm /25.4=inches TYPICAL PROPERTIES N x 0.225=lb/F Physical Properties N/mm x 5.71=lb/in Hardness, Shore A,ASTM D2240 80 psi x 145=N/mm Breaking Strength ,ASTM D1458,KN/m 1 MPa =N/mm Flammability Rating, UL 94 V-0 Nm x 8.851 = lbin Nm x 0.738=lbft Nmm x 0.142=ozin Electrical Properties mPas =cP Dielectric Breakdown Voltage ,ASTM D149,Vac 5,000 Dielectric Constant ,ASTM D150 1,000 Hz 5.5 11 Volume Resistivity ,ASTM D257,ohm-meter 110 Thermal Properties Thermal Conductivity ,ASTM D5470,W/(m-K) 0.9 2 (1) Thermal Impedance ,ASTM D5470,C-in /W 0.6 I)The ASTM D5470test fixture was used. The recorded value includes interfacial thermal resistance. These values are provided for reference only. Actual application performance is directly related to the surface roughness, flatness and pressure applied.TDS BERGQUIST SILPAD TSP T1200 , February -2020 Disclaimer Note: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. The product can have a variety of different applications as well as differing application and working conditions in your environment that are beyond our control. Henkel is, therefore, not liable for the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liability in respect of the information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except if otherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Belgium NV, Henkel Electronic Materials NV,Henkel Nederland BV,Henkel Technologies France SAS and Henkel France SA please additionally note the following: In case Henkel would be nevertheless held liable,on whatever legal ground, Henkels liability will in no event exceed the amount of the concerned delivery. In case products are delivered by Henkel Colombiana, S.A.S.the following disclaimer is applicable: The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the product are based on our knowledge and experience of the product as at the date of this TDS. Henkel is, therefore, not liable for the suitability of our product for the production processes and conditions in respect of which you use them, as well as the intended applications and results. We strongly recommend that you carry out your own prior trials to confirm such suitability of our product. Any liability in respect of the information in the Technical Data Sheet or any other written or oral recommendation(s) regarding the concerned product is excluded, except ifotherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liability under any applicable mandatory product liability law. In case products are delivered by Henkel Corporation, Resin Technology Group, Inc., or Henkel Canada Corporation, the following disclaimer is applicable: The data contained herein are furnished for information only and are believed to be reliable. We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons against any hazards that may be involved in the handling and use thereof. In light of the foregoing, Henkel Corporation specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel Corporations products. Henkel Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications. Trademark usage Except as otherwise noted, all trademarks in this document are trademarks of Henkel Corporation in the U.S. and elsewhere. denotes a trademark registered in the U.S. Patent and Trademark Office. Reference N/A Americas Europe Asia +1.888.943.6535 +32.1457.5611 +86.21.2891.8000 For the most direct access to local sales and technical support visit: www.henkel.com/electronics